Mitsubishi Electric Melsensor CF26-LR страница 42 Скачать руководство пользователя | Manualshive

Страница: 42 / 112

background image

40

7 SETTING CODE READER
7.2 Settings in Tune

7.2

Settings in Tune

Tune is a function to optimize focus, brightness (exposure and gain), and lightning patterns. The code reader can be
configured easily by using tuning function.
The following shows the procedure for setting parameters using Tune.

Preparation for tuning

• Set symbols to be read in [Code Details] of [Application Steps]. Some symbols are initially set as an enabled symbol.

A codes which is not set as an enabled symbol is not detected during tuning. Check if the symbol of the target
code is enabled before tuning.

• Click the [Live] button in [Optimize Image] of [Application Steps] to switch to Live mode.
• Locate a target code close to the center of the reading range while checking 'Image Panel.'
* However, the image is blurred at this point because the image is not focused.
• A green light emitted from a code reader is a sighting light called aimer. Locate a read target code to the center of the aimer.
* "Aimer Enabled" needs to be enabled.

• When the installation location of the read target code is determined, click the [Live] button again to end Live mode.

Execute tuning

Tuning is started by clicking the [Tune] button.
The [Tune] button is switched to [Cancel] button during tuning.
During tuning, red, yellow and green circles are displayed on Image Panel and the process of adjusting a focus can be
checked. A code surrounded by a green frame indicates that the code is recognized by the code reader. Additionally, a fine
adjustment of a focus, brightness adjustment, and lightning pattern adjustment are performed.

When tuning is completed, the [Cancel] button is switched to [Tune].

When adjusting a focus

When the code is recognized

«
...
40
41
42
43
44
...
»

Содержание Melsensor CF26-LR

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Melsensor CF26-LR

Бренд: Unitech Страницы: 2

Бренд: Unitech Страницы: 17

Бренд: Unitech Страницы: 6

Бренд: Unitech Страницы: 2

Бренд: Unitech Страницы: 2

Бренд: Unitech Страницы: 3

Бренд: Yarvik Страницы: 222

Бренд: Alien Страницы: 41

Бренд: Conceptronic Страницы: 21

Бренд: Lindy Страницы: 4

Бренд: Onyx International Страницы: 38

Бренд: Citizen Страницы: 107

iCLASS SE RKCLB40E

Бренд: HID Страницы: 31

Бренд: Billow Страницы: 95

Бренд: Unitech Страницы: 109

SensArray Enterprise

Бренд: SensThys Страницы: 13

Бренд: Dataman Страницы: 7

Бренд: Access Interfacing Solutions Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды