Mitsubishi Electric MELSEC iQ-R60DA4 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 68

background image

8 OFFSET/GAIN SETTING

8.1 Setting Procedure

51

8

8

OFFSET/GAIN SETTING

When using the user range setting, configure the offset/gain setting.
Access to the offset/gain setting window in the engineering tool to set the offset/gain setting.

8.1

Setting Procedure

This section describes the setting procedure for the offset/gain setting of the D/A converter module. In wave output mode, the
offset/gain setting cannot be accessed. Change the mode to the normal output mode or the offset/gain setting mode in
advance.
Do not turn off the external power supply in the middle of the offset/gain setting. Otherwise, the offset/gain setting is not
properly applied.

[Tool]



[Module Tool List]

1.

Select "Analog Output"



"Offset/gain setting" and click

the [OK] button.

2.

Select the target module for the offset/gain setting, and
click [OK] button.

3.

Click the [Yes] button.

«
...
51
52
53
54
55
...
»

Содержание MELSEC iQ-R60DA4





































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R60DA4

Бренд: Watts Страницы: 2

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 358

Бренд: Fagor Страницы: 556

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 180

Бренд: Fagor Страницы: 112

Master Control Unit

Бренд: FaderMate Страницы: 36

Бренд: V2 ELETTRONICA Страницы: 72

Бренд: Lamtec Страницы: 136

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Vacon Страницы: 132

Бренд: +GF+ Страницы: 3

Бренд: Össur Страницы: 58

Бренд: Game ready Страницы: 24

Бренд: nvent Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды