Mitsubishi Electric MELIPC MI5000 Series Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 320

Mitsubishi Electric MELIPC MI5000 Series Скачать руководство пользователя страница 184

182

17 BASIC PARAMETERS
17.3 Refresh Setting

17.3

Refresh Setting

Set refresh parameters.

Window

Displayed items

Item

Description

Setting range

Link Side

The number of points for the link devices (RX/RY, RWr/RWw) for the
number of occupied stations and start/end device number set in the network
configuration settings are displayed.



MELIPC side

Target

The target for link refresh is displayed.

Specify Device

device name

Set the device of the link refresh target.

M, B, D, W, ZR

Points

The number of device points subject to link refresh is displayed. (A value the
same as the number of points of the link side is displayed. )



Start

Set the start device number within the link refresh range.

• M: 0 to 61439
• B: 0 to 9FFFFH
• D: 0 to 4184063
• W: 0 to FFFFFH
• ZR: 0 to 524287

End

The end device number within the link refresh range is displayed.



«
...
182
183
184
185
186
...
»

Содержание MELIPC MI5000 Series

































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды