Mitsubishi Electric MELIPC MI5000 Series Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 320

Mitsubishi Electric MELIPC MI5000 Series Скачать руководство пользователя страница 118

116

8 DIAGNOSTIC AND MAINTENANCE FUNCTIONS
8.5 Switch/LED Operation Function

LED status acquisition function

This function acquires the statuses of the main LED, dot matrix LED, and the CC-Link IE Field Network LED of this product.
The following table shows the LEDs for which LED statuses can be acquired.



: Possible,



: Impossible

LED status acquisition

Acquire the LED statuses using the C Controller module dedicated functions (CCPU_GetLEDStatus,
CCPU_GetDotMatrixLED, CCPU_GetDotMatrixLED_ISR).

■

Function list

For details on the C Controller module dedicated functions, refer to the following manual.



MELIPC MI5000 Series Programming Manual (VxWorks)

LED name

Acquisition
applicability

MAIN LED

VX RDY LED



WIN RDY LED

MAIN ERR LED

MAIN RUN LED

STORAGE LED



FAN LED



INFO LED

RS SD/RD LED



BATTERY LED



CC-Link IE Field Network LED

RUN LED



ERR LED

MST LED

D LINK LED

SD/RD LED

L ERR LED

Dot matrix LED



Function name

Description

CCPU_GetLEDStatus

Acquires the LED status of a MELIPC.

CCPU_GetDotMatrixLED

Acquires the values displayed on the dot matrix LED of a MELIPC.

CCPU_GetDotMatrixLED_ISR

«
...
116
117
118
119
120
...
»

Содержание MELIPC MI5000 Series

































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды