7 - 15
MDS-D-SVJ3/SPJ3 Series Specifications Manual
7-3 Selection of the regenerative resistor
7-3-2 Calculation of the regenerative energy
Calculate the regenerative energy for stopping from each axis' rapid traverse rate (maximum rotation speed
for spindle), and select a regenerative resistor having a capacity that satisfies the positioning frequency
determined from the machine specifications.
(1) For horizontal servo axis and spindle
The regenerative energy E
R
consumed by the regenerative resistor can be calculated from expression (7-
13). If the E
R
value is negative, all of the regenerative energy is absorbed by the capacitor in the drive unit
(capacitor regeneration), and the energy consumed by the regenerative resistor is zero (E
R
= 0).
••• (7-13)
(Example)When a load with the same inertia as the motor is connected to the HF54, determine the
regenerative energy to stop from the rated rotation speed. Note that the drive unit is MDS-D-SVJ3-07NA in
this case.
According to expression (7-13), the regenerative energy E
R
is:
E
R
=5.48×10
-7
×0.85×(6.1+6.1)×3000
2
-18 =33.1(J)
Drive unit charging energy
Motor reverse efficiency
η
:Motor reverse efficiency
J
L
:Motor inertia
(kg•cm
2
)
J
M
:Load inertia
(kg•cm
2
)
N
:Motor speed
(r/min)
Ec
:Unit charging energy
(J)
Drive unit
Charging energy Ec (J)
Drive unit
Charging energy Ec(J)
MDS-D-SVJ3-03NA
9
MDS-D-SPJ3-075NA
18
MDS-D-SVJ3-04NA
11
MDS-D-SPJ3-22NA
40
MDS-D-SVJ3-07NA
18
MDS-D-SPJ3-37NA
40
MDS-D-SVJ3-10NA
30
MDS-D-SPJ3-55NA
45
MDS-D-SVJ3-20NA
40
MDS-D-SPJ3-75NA
45
MDS-D-SVJ3-35NA
40
MDS-D-SPJ3-110NA
90
Motor
Motor reverse
efficiency
η
Motor
Motor reverse
efficiency
η
HF75,105
0.85
All spindle motors
0.90
HF54, 104, 154, 224, 123, 223, 142
0.85
HF204, 354, 303, 302
0.85
HF-KP13
0.55
HF-KP23
0.70
HF-KP43
0.85
HF-KP73
0.85
The charging energy values apply when the unit input power voltage is 220V. If the input voltage is
higher, the charging energy decreases, and the regenerative energy increases.
E
R
䋽
5.48 × 10
-7
(J
L
䋫
J
M
)
䍃
N
2
䋭
Ec
(J)
・
・
POINT
Содержание MDS-D-SPJ3
