This manual confers no industrial property rights or any rights of any other
kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation
cannot be held responsible for any problems involving industrial property rights
which may occur as a result of using the contents noted in this manual.
Warranty
Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for
compensation to:
(1) Damages caused by any cause found not to be the responsibility of
Mitsubishi.
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
products.
(3) Special damages and secondary damages whether foreseeable or not,
compensation for accidents, and compensation for damages to products
other than Mitsubishi products.
(4) Replacement by the user, maintenance of on-site equipment, start-up test run
and other tasks.
For safe use
This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Side
A
Side
B
JAPANESE
ENGLISH
JY997D22901R
Side
B
GT1020-L
D(W)/L
D(W)2/L
L(W)
GT10 General Description
This manual describes the specifications of the product. Before use, read this
manual and manuals of relevant products fully to acquire proficiency in handling
and operating the product. Make sure to learn all the product information, safety
information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
Effective Oct. 2016
Specifications are subject to change without notice.
2008 MITSUBISHI ELECTRIC CORPORATION
Manual Number
JY997D22901R
Date
Oct. 2016
Safety Precaution
(Read these precautions before using.)
Before using this product, please read this manual and the relevant manuals
introduced in this manual carefully and pay full attention to safety to handle the
product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
DESIGN PRECAUTIONS
Some failures of the GOT or cable may keep the outputs on or off.
An external monitoring circuit should be provided to check for output signals
which may lead to a serious accident.
Not doing so can cause an accident due to false output or malfunction.
If a communication fault (including cable disconnection) occurs during
monitoring on the GOT, communication between the GOT and PLC CPU is
suspended and the GOT becomes inoperative.
A system where the GOT is used should be configured to perform any
significant operation to the system by using the switches of a device other
than the GOT on the assumption that a GOT communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
Do not use the GOT as the warning device that may cause a serious
accident. An independent and redundant hardware or mechanical interlock is
required to configure the device that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect
output or malfunction.
Incorrect operation of the touch switch(s) may lead to a serious accident if the
GOT backlight is gone out. When the GOT backlight goes out, causes the
monitor screen to appear blank, while the input of the touch switch(s) remains
active. This may confuse an operator in thinking that the GOT is in
"screensaver" mode, who then tries to release the GOT from this mode by
touching the display section, which may cause a touch switch to operate.
DESIGN PRECAUTIONS
Do not bundle the control and communication cables with main-circuit, power
or other wiring.
Run the above cables separately from such wiring and keep them a minimum
of 100mm (3.94in.) apart.Not doing so noise can cause a malfunction.
Do not press the GOT display section with a pointed material as a pen or
driver. Doing so can result in a damage or failure of the display section.
Before connecting to GOT, turn ON the controller to enable the
communication. When the communication of controller is not available, a
communication error may occur in GOT.
MOUNTING PRECAUTIONS
Be sure to shut off all phases of the external power supply used by the system
before mounting or removing the GOT to/from the panel.
Not doing so can cause the unit to fail or malfunction.
MOUNTING PRECAUTIONS
Use the GOT in the environment that satisfies the general specifications
described in this manual. Not doing so can cause an electric shock, fire,
malfunction or product damage or deterioration.
When mounting the GOT to the control panel, tighten the mounting screws in the
specified torque range. Undertightening can cause the GOT to drop, short circuit
or malfunction, and deteriorate the waterproof effect and oilproof effect.
Overtightening can cause a drop, short circuit or malfunction due to the damage
of the screws or the GOT, and deteriorate the waterproof effect and oilproof effect
due to distortion of the protective cover for oil, GOT or panel.
When using the GOT in the environment of oil or chemicals, use the protective
cover for oil. Failure to do so may cause failure or malfunction due to the oil or
chemical entering into the GOT.
WIRING PRECAUTIONS
Be sure to shut off all phases of the external power supply used by the system
before wiring. Failure to do so may result in an electric shock, product damage or
malfunctions.
Please make sure to ground FG terminal of the GOT power supply section by
applying 100 or less which is used exclusively for the GOT. Not doing so may
cause an electric shock or malfunction.
Correctly wire the GOT power supply section after confirming the rated voltage
and terminal arrangement of the product. Not doing so can cause a fire or failure.
Tighten the terminal screws of the GOT power supply section in the specified
torque range. Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the
screws or the GOT.
Exercise care to avoid foreign matter such as chips and wire offcuts entering the
GOT. Not doing so can cause a fire, failure or malfunction.
WIRING PRECAUTIONS
Plug the communication cable into the connector of the connected unit and
tighten the mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction. Overtightening can
cause a short circuit or malfunction due to the damage of the screws or unit.
TEST OPERATION
PRECAUTIONS
Before performing the test operations of the user creation monitor screen (such as
turning ON or OFF bit device, changing the word device current value, changing
the settings or current values of the timer or counter), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to
perform significant operation for the system. False output or malfunction can
cause an accident.
STARTUP/MAINTENANCE
PRECAUTIONS
When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
Before starting cleaning or terminal screw retightening, always switch off the
power externally in all phases. Not switching the power off in all phases can cause
a unit failure or malfunction. Undertightening can cause a short circuit or
malfunction. Overtightening can cause a short circuit or malfunction due to the
damage of the screws or unit.
STARTUP/MAINTENANCE
PRECAUTIONS
Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling,
motion or accidental pulling of the cables or can cause a malfunction due to a
cable connection fault.
When unplugging the cable connected to the unit, do not hold and pull the cable
portion. Doing so can cause the unit or cable to be damaged or can cause a
malfunction due to a cable connection fault.
Before touching the unit, always touch grounded metal, etc. to discharge static
electricity from human body, etc.
Not doing so can cause the unit to fail malfunction.
Compliance with EC directive (CE Marking)
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Attention
This product is designed for use in industrial applications.
Requirement for Compliance with EMC directive
The following products have shown compliance through direct testing (to the
identified standards) and design analysis (forming a technical construction file) to the
European Directive for Electromagnetic Compatibility (2004/108/EC) when used as
directed by the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
For more details please contact the local Mitsubishi Electric sales site.
Notes for compliance to EMC regulation
1) General notes on the use of communication cables
Any device which utilizes a data communication function is susceptible to the
wider effects of local EMC noise. Therefore, when installing any communication
cables care should always be taken with the routing and location of those cables.
The GOT units identified on the previous chapter are compliant with the EMC
requirement when the following communication cables are used.
2) General notes on the use of the power cable
The GT1020-LBD/LWD/LBD2/LWD2/LBDW/LWDW/LBDW2/LWDW2 unit
demand that the cable for the power supply is 10m or less.
Associated Manuals
*1 Stored in the GT Works2/GT Designer2/GT Works3/GT Designer3 in PDF format.
For details of a PLC to be connected, refer to the PLC user's manual respectively.
Bundled Items
「电器电子产品有害物质限制使用标识要求」的表示方式
Note: This symbol mark is for China only.
含有有害6物质的名称，含有量，含有部品
本产品中所含有的有害 6 物质的名称，含有量，含有部品如下表所
示。
产品中有害物质的名称及含量
本表格依据SJ/T 11364的规定编制。
○:表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572
规定的限量要求以下。
×:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T
26572规定的限量要求。
DISPOSAL PRECAUTIONS
When disposing of the product, handle it as industrial waste.
TOUCH PANEL
PRECAUTIONS
For the analog-resistive film type touch panels, normally the adjustment is not
required. However, the difference between a touched position and the object
position may occur as the period of use elapses. When any difference between
a touched position and the object position occurs, execute the touch panel
calibration.
When any difference between a touched position and the object position occurs,
other object may be activated. This may cause an unexpected operation due to
incorrect output or malfunction.
TRANSPORTATION
PRECAUTIONS
Make sure to transport the GOT main unit and/or relevant unit(s) in the manner
they will not be exposed to the impact exceeding the impact resistance
described in the general specifications of this manual, as they are precision
devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
Standard
Remark
EN61131-2 : 2007
Programmable
controllers-
Equipment,
requirement and tests
EMI
Compliance with all relevant aspects of the
standard. (Radiated Emissions)
EMS
Compliance with all relevant aspects of the
standard.
(ESD,RF electromagnetic field, EFTB, Surge, RF
conducted disturbances and Power frequency
magnetic field)
GOT Unit
Existing Cables
G T 10 2 0- L B D / LW D , G T1 0 2 0- LB L/ LW L,
GT1020-LBDW/LWDW, GT1020-LBLW/LWLW
GT10-C30R4-8P (For Melsec
FX series PLC)
GT1020-LBD2/LWD2, GT1020-LBDW2/
LWDW2
GT10-C30R2-6P (For Melsec
Q series PLC)
Manual name
Contents
Manual Number
(Model Code)
G T 1 0 U s e r ' s
Manual
( s o l d
separately)
Describes the GT10 hardware-relevant
co nte nt suc h as part n ames , ext ernal
dimensions, mounting, power supply wiring,
specifications, and introduction to option
devices
JY997D24701
(09R819)
Manual name
Contents
Manual Number
(Model Code)
G O T 1 0 0 0 S e r i e s
Connection Manual 1/3,
2/3, 3/3
(sold separately)
*1
Describes system configurations
o f t h e c o n n e c t i o n m e t h o d
applicable to GOT1000 series and
cable creation method
SH-080532ENG
(1D7M26)
GT Designer2 Version2
Basic Operation/Data
Transfer Manual (For
GOT1000 Series)
(sold separately)
*1
Describes methods of the GT
Designer2 installation operation,
basic operation for drawing and
transmitting data to GOT1000
series
SH-080529ENG
(1D7M24)
GT Designer2 Version2
Screen Design Manual
(For GOT1000 Series) 1/
3, 2/3, 3/3
(sold separately)
*1
Describes specifications and
settings of the object functions
used in GT Designer2
SH-080530ENG
SH-080531ENG
(1D7M25)
GT Designer3
Version1 Screen
Design Manual
(For GOT1000 Series)
(Fundamentals)
1/2, 2/2
(sold separately)
*1
Describes methods of the GT
Designer3 installation operation,
basic operation for drawing and
transmitting data to GOT1000
series
SH-080866ENG
(1D7MB9)
GT Designer3
Version1 Screen Design
Manual
(For GOT1000
Series)
(Functions) 1/2, 2/2
(sold separately)
*1
Describes specifications and
settings of the object functions
used in GT Designer3
SH-080867ENG
(1D7MC1)
Model Name
Remark
GT1020-LBD/LWD
GOT main unit
(The maintenance supplies below are packed with the
product.)
GT1020-LBD2/LWD2
GT1020-LBL/LWL
GT1020-LBDW/LWDW
GT1020-LBDW2/LWDW2
GT1020-LBLW/LWLW
Maintenance Supplies
Quantity
PLC Communication Connector
1
Panel Mounting Bracket (with M4
20 screws)
4
Panel Mounting Packing
1
GT10 General Description (This manual)
1
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴
二苯醚
(PBDE)
显 示 器
GOT
外壳
○
○
○
○
○
○
印刷基板
×
○
○
○
○
○
1. Specifications
1.1 General Specifications
*1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press,
and the sheet may be peeled off.
*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
1.2 Performance Specifications
Item
Specifications
GT1020-LBD/LWD/LBD2/LWD2/LBL/LWL/LBDW/LWDW/LBDW2/LWDW2/LBLW/LWLW
Operating ambient
temperature
Display section
0 to 50
C
Other than display section 0 to 55
C (When mounted horizontally), 0 to 50
C (When mounted vertically)
Storage ambient temperature
-20 to 60
C
Operating/Storage ambient humidity
10 to 90% RH, non-condensing (The wet bulb temperature is 39
C or less.)
Vibration resistance
Conforms to JIS
B3502 and
IEC61131-2
Frequency
Acceleration
Half-amplitude
Sweep Count
Under intermittent
vibration
5 to 9Hz
--
3.5mm
10 times each in X,
Y and Z directions
9 to 150Hz
9.8m/s
2
--
Under continuous
vibration
5 to 9Hz
--
1.75mm
9 to 150Hz
4.9m/s
2
--
Shock resistance
Conforms to JIS B3502, IEC 61131-2 (147m/s
2
, 11 ms, Sine half-wave pulse, 3 times each in the X, Y, and Z directions.)
Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles and
must be no direct sunlight. (Same as for saving)
Operating altitude
*1
2000 m (6562 ft) max.
Installation location
Inside control panel
Overvoltage category
*2
II or less
Pollution degree
*3
2 or less
Cooling method
Self-cooling
Item
Specifications
GT1020-LBD/LWD/LBD2/
LWD2
GT1020-LBL/LWL
GT1020-LBDW/LWDW/
LBDW2/LWDW2
GT1020-LBLW/LWLW
Display
section
*1
Type
STN monochrome (white/black) liquid crystal
Screen size
3.7"
Resolution
160
64 dots (Horizontal format)
Display size
W86.4(3.4)
H34.5(1.35) [mm](inch) (Horizontal format)
Display character
16-dot standard font: 20 characters
4 lines (Horizontal format)
Display color
Monochrome (white/black)
Display angle
Left/Right: 30 degrees, Top: 20 degrees, Bottom: 30 degrees (Horizontal format)
Contrast adjustment
16-level adjustment
Intensity of LCD only
200 [cd/m
2
] (in green)
300 [cd/m
2
] (in white)
Life
Approx. 50,000h. (Time for display intensity to become 1/5 at operating ambient temperature of 25
C)
Backlight
(no replacement required)
LED with 3 available colors (green, red, orange)
LED with 3 available colors (white, red, pink)
Backlight status (colors, ON/BLINK/OFF) control, Adjustable screensaver activation time
Setting the system information enables
*2
PLC to control the backlight status
Touch
panel
Number of touch keys
Maximum 50 keys/screen (Analog resistive film touch panel)
Key size
Minimum 2
2 dots (per key)
Simultaneous pressing of
two (or more) areas
(2-point press)
Not supported
(Simultaneous pressing of two or more areas on the screen may activate the switch between those areas.)
Life
1 million times or more (operating force 0.98N max.)
Memory
C drive
*3
Flash memory ROM (Internal), for storing Project data (512kbytes or less), OS, Alarm history and Recipe data
Life
(Number of write times)
100,000 times
Buzzer output (a buzzer that sounds
when touch keys are pressed)
Single tone (LONG/ SHORT/ OFF adjustable)
Environmental protective structure
*4
Equivalent to IP67 (JEM1030) (front section)
External dimensions
W113(4.44)
H74(2.91)
D27(1.06)[mm](inch) (Excluding mounting fixtures) (Horizontal format)
Panel cutting dimensions
W105 (4.13)
H66 (2.59) [mm] (inch) (Horizontal format)
Weight (Excluding mounting fixtures) 0.2kg
0.18kg
0.2kg
0.18kg
Compatible software package
GT Designer2 Version2.43V or later/
GT Designer3 Version1.01B or later
GT Designer2 Version2.58L or later/
GT Designer3 Version1.01B or later
*1 • Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal
display panel. It is impossible to completely avoid this symptom, as the
liquid crystal display comprises of a great number of display elements.
Flickers may be observed depending on the display color. Please note that
these dots appear due to its characteristic and are not caused by product
defect.
• Flickers and partial discoloration may be generated on the liquid crystal
display panel due to the display contents or the contrast adjustment.
However, please note that these phenomena appear due to its
characteristic and are not caused by product defect.
• There is a difference in the display brightness and the color tones between
liquid crystal display panels. When using multiple liquid crystal display
panels, please note that there is an individual difference between them.
• A crosstalk (shadow as an extension of the display) may appear on the
liquid crystal display panel. Please note that it appears due to its
characteristic.
• When the display section is seen from the outside of the display angle, the
display color seems like it has changed.
Please note that it is due to its characteristic. Please note that the
response time, brightness and color of the liquid crystal display panel may
vary depending on the usage environmental temperature.
Especially in the low temperature environment, the display response
becomes slow due to the characteristics of the STN liquid crystal.
Please check the display response in advance for using this product.
• When the same screen is displayed for a long time, an incidental color or
partial discoloration is generated on the screen due to heat damage, and it
may not disappear. To prevent heat damage, the screen saver function is
effective. For details on the screen saver function, refer to the following.
GT10 User's Manual
*2 For the details of system information, refer to the following.
GT Designer2 Version
Screen Design Manual
GT Designer3 Version1 Screen Design Manual
*3 ROM in which new data can be written without deleting the written data.
*4 Note that this does not guarantee all users' operation environment.
In addition, the product may not be used in environments under exposition of
oil or chemicals for a long period of time, or in environments filled with oil-mist.
1.3 Communication Specifications
*1 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.
For details of GOT multidrop connection, refer to the following.
GOT1000 Series Connection Manual
*2 Project data upload/download, OS installation, Transparent function
1.4 Power Supply Specifications
(
For details on power supply wiring, such as the allowable cable size and tightening torque, refer to the additional manual, "GT10 User's Manual".)
*1 The GOT continues to operate even upon 5ms or shorter instantaneous
power failure. The GOT stops operating if there is extended power failure or
voltage drop, while it automatically resumes operation as soon as the power is
restored.
2. Wiring of connection cable
The diagram below shows cable assignment for GOT port.
Cables: GT10-C
R4-8P, GT10-C
R4-2P, GT10-C
R2-6P
User-made cable is necessary, depending on the PLC.
For the detail, refer to GOT1000 Series Connection Manual.
Item
Specifications
GT1020-LBD/LWD/LBDW/LWDW
GT1020-LBD2/LWD2/LBDW2/LWDW2
GT1020-LBL/LWL/LBLW/LWLW
PLC communication
Communication standard RS-422/485, 1ch
RS-232, 1ch
RS-422, 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
Connector terminal block 9-pins
Terminating resistor
*1
Open/110
/330
(Switched by
terminating resistor selector switch)
(At factory shipment: 330
)
--
--
PC communication
*2
Communication standard RS-232, 1ch
Transmission speed
115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
MINI DIN 6-pins (Female)
Item
Specifications
GT1020-LBD/LWD/LBD2/LWD2/LBDW/LWDW/LBDW2/LWDW2
GT1020-LBL/LWL/LBLW/LWLW
Input power supply voltage
24VDC (+10% -15%), ripple voltage 200mV or less
5VDC (
5%), supplied from the PLC
Fuse (built-in, not exchangeable)
0.4A
–
Power consumption, (At backlight off)
1.9W (80mA/24VDC) or less, (1.2W (50mA/24VDC) or less)
1.1W (220mA/5VDC) or less, (0.6W (120mA/5VDC) or less)
Inrush current
13A or less (26.4VDC) 1ms
–
Permissible instantaneous power failure time
*1
Within 5ms
–
Noise immunity
Noise voltage: 1000Vp-p, Noise width: 1
s (by noise simulator of 30 to 100Hz noise frequency)
Dielectric withstand voltage
500VAC for 1 minute (between the GOT’s power supply terminals
and the GOT’s grounding terminal)
–
Insulation resistance
10M
or larger by insulation resistance tester (between the GOT’s
power supply terminals and the GOT’s grounding terminal)
–
Grounding
Grounding with a ground resistance of 100
Ω
or less by using a
ground cable that has a cross-sectional area of 0.14 to 1.5 mm
2
(solid wire), 0.14 to 1.0 mm
2
(stranded wire), or 0.25 to 0.5 mm
2
(rod terminal with an insulation sleeve). If impossible, connect the
ground cable to the control panel.
–
Cable jacket to remove
7mm (0.27")
Tightening torque
0.22 to 0.25 N
m
Recommended Tool (Screwdriver)
SZS 0.4
2.5 (Phoenix Contact Inc.)
PLC connection cable
GOT
PLC
24V
GOT
5V
CSB
CSA
SDA
SDB
RDA
RDB
SG
RSA
RSB
Untied
wire
color
Brown
Red
Orange
Yellow
Green
Black
White
24V
SDA
SDB
RDA
RDB
SG
RSA
RSB
CSB
CSA
GOT
SD
RD
ER
DR
SG
RS
CS
NC
NC
Blue
Yellow
Green
Purple
Blue
Purple
24V
-
+
(terminal
block)
GOT
Untied
wire
color
(terminal
block)
Brown
Red
Orange
Yellow
Green
Black
White
(terminal
block)
Brown
Red
Untied
wire
color
GT10-C R4-8P
GT10-C R4-25P
GT10-C R2-6P
