manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 102

97

Adjustment of the output torque (current) of the motor

4

P

ARAM

ETE

R

S

(2) Setting of stall prevention operation level 

(Pr. 22)

(3) Stall prevention operation signal output and output timing adjustment 

(OL signal, Pr. 157)

When the output current exceeds the stall prevention operation level and stall prevention is activated, the stall prevention

operation signal (OL signal) turns ON for longer than 100ms. When the output current falls to or below the stall prevention
operation level, the output signal turns OFF.

Use 

Pr. 157 OL signal output timer 

 to set whether the OL signal is output immediately or after a preset period of time.

This operation is also performed when the regeneration avoidance function or 

(overvoltage stall) is executed.

For the OL signal, set "3 (positive logic) or 103 (negative logic)" in 

Pr. 190

 

or

 

Pr. 192 (output terminal function selection) 

 and

assign the function to the output terminal.

For 

Pr. 22

, set the output current level where the stall 

prevention is activated. Set the output current level in ratio to 
the rated inverter current (rated IPM motor current under IPM 
motor control). Normally set 120% (initial value).

Stall prevention operation stops acceleration (makes 
deceleration) during acceleration, makes deceleration during 
constant speed, and stops deceleration (makes acceleration) 
during deceleration.

When stall prevention operation is performed, the OL signal is 
output.

NOTE

If an overload status lasts long, an inverter trip (e.g. electronic thermal O/L relay (E.THM)) may occur.

Pr. 157 

Setting

Description

0

(initial value)

Output immediately.

0.1 to 25

Output after the set time (s) has elapsed.

9999

Not output.

NOTE

If the frequency has fallen to 1Hz by stall prevention operation and remains for 3s, a fault (E.OLT) appears to trip the
inverter output.

Changing the terminal assignment using 

Pr. 190 and Pr. 192 (output terminal function selection) 

may affect the other

functions. Set parameters after confirming the function of each terminal.

Stall prevention operation example

Pr. 22

OL

Output current

Acceleration

Time

Constant  
speed

Deceleration

Output frequency

Overload state (OL operation)

OL output signal

Pr. 157 

set time(s)

Содержание FR-F700PJ Series





































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды