Mitsubishi Electric FDF100VNVD Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 211

background image

-

123

-

'11 • PAC-T-160

■

Error log and reset

Error indicator

Memorized error log

Reset

Remote controller display

• Higher priority error is memorized.

• Stop the unit by pressing the ON/OFF

switch of remote controller.

• If the unit has recovered from anomaly, it

can be operated.

Red LED on indoor control PCB

• Not memorized.

Red LED on outdoor control PCB

• Memorizes a mode of higher priority.

■

Resetting the error log

• Resetting the memorized error log in the remote controller
Holding down “CHECK” button, press “TIMER” button to reset the error log memorized in the remote controller.
• Resetting the memorized error log
The remote controller transmits error log erase command to the indoor unit when “VENTI” button is pressed while

holding down “CHECK” button.

Receiving the command, the indoor unit erase the log and answer the status of no error.

(2) Troubleshooting procedure

When any trouble has occurred, inspect as follows. Details of respective inspection method will be described on later pages.

Trouble

Confirmation

of power

supply

(Indoor/

outdoor unit)

Confirmation of

remote controller and

LEDs on the PCB

of indoor unit and

outdoor unit (Indoor/

outdoor unit, remote

controller)

Check of the anomalous

operation data on the

remote controller

Inspection

of the unit/

controller

Replacement/

repair of

faulty part,

test run,

adjustment

(3) Troubleshooting at the indoor unit

With the troubleshooting, find out any defective part by checking the voltage (AC, DC), resistance, etc. at respective connectors

at around the indoor PCB, according to the inspection display or operation status of unit (the compressor does not run, fan does
not run, the 4-way valve does not switch, etc.), and replace or repair in the unit of following part.

(a) Replacement part related to indoor PCB’s

Control PCB, power supply PCB, temperature thermistor (return air, indoor heat exchanger), remote controller switch,
limit switch, transformer and fuse

Note (1) With regard to parts of high voltage circuits and refrigeration cycle, judge it according to ordinary inspection methods.

«
...
122
123
124
125
126
...
»

Содержание FDF100VNVD




















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FDF100VNVD

Бренд: GE Страницы: 2

Бренд: KeepRite Страницы: 16

Бренд: Samsung Страницы: 40

Бренд: WINEMASTER Страницы: 16

Бренд: E-Tac Страницы: 24

TC 200 SPLIT Series

Бренд: Gorenje Страницы: 40

Бренд: EINHELL Страницы: 52

Бренд: Clatronic Страницы: 62

Бренд: edc Страницы: 46

Бренд: Rotenso Страницы: 16

Thru-the-Wall Air Conditioners

Бренд: Friedrich Страницы: 6

Бренд: Linea 2000 Страницы: 94

Бренд: Daikin Страницы: 20

ProShield Plus Ai

Бренд: Oreck Страницы: 10

P/N9359944072-01

Бренд: Friedrich Страницы: 20

Бренд: Olimpia splendid Страницы: 24

Бренд: Envicool Страницы: 31

Бренд: Oransi Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды