manualshive.com logo in svg

Mitsubishi Electric CR750 Series, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi Electric CR750 Series Скачать руководство пользователя страница 383

                            

4

MELFA-BASIC V

   

Detailed explanation of Robot Status Variable

   4-363

M_SplPno

[Function]

During spline interpolation, the number of the path point passed through most recently is returned.
The spline interpolation start position is 1.

Note) This command is supported with software version R5 or later (F-Q series) or S5 or later (F-D series).

[Format]

[Terminology]

<Numeric Variable>

Designates the numerical variable substituted for the reference results.

<Mechanism Number>

Sets the mechanism No. that executes spline interpolation. 
Setting range: 1 to 3 
When omitted: 1 
If a non-existent mechanism No. is designated, the error L3870 (designated 
mechanism No. invalid) will occur when execution is started.

[Reference Program]

1 Wait M_00=1

' Wait for spline interpolation to start

2 *L1:If M_SplPno < 5 Then GoTo *L1

' Wait for path point 5 to be passed

3 M1=M_Inw(100)

' After passing through path point 5, get input signal 100 to 115 

status

4 *L2:If M_SplPno < 10 Then GoTo *L2

' Wait for path point 10 to be passed

5 M_01=M1

' After passing through path point 10, substitute M1 details in 

M_01

[Explanation]

(1) During spline interpolation, the number of the path point passed through most recently is returned.
(2) By referring to the M_SplPno value with multi-task, the operation process or signal output, etc., can be 

executed according to the progress of spline interpolation.

(3) M_SplPno returns the value indicated in the following table according to the state.

Table 4-32:Value returned by M_SplPno

(4) M_SplPno is a read-only status variable.

Example) <Numeric Variable>=M_SplPno [(<Mechanism Number>)]

Status

Value returned by M_SplPno

Immediately after power ON

0

During spline interpolation execution

1 to (value corresponding to progress of spline 
interpolation)

After spline interpolation

Path point No. for end position of spline interpola-
tion

Immediately after main program’s End 
command is executed

0

Immediately after program reset operation

0

Mechanism not compatible with spline 
interpolation

0

Содержание CR750 Series



























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды