manualshive.com logo in svg

Mitsubishi Electric CR750 Series, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi Electric CR750 Series Скачать руководство пользователя страница 269

                              

4

MELFA-BASIC V

   

Detailed explanation of command words

   4-249

Loadset (Load Set)

[Function]

This instruction specifies the condition of the hand/workpiece at execution of the Oadl instruction.
And, when using the interference avoidance function, specify the hand number and the work number. (Spec-
ify the model which is the target of the interference check)

[Format]

[Terminology]

<Hand  condition  No.>

1 to 8.Designate the hand condition (HNDDAT 1 to 8) No. for which the weight and 

size are designated. 

<Workpiece condition No.>

1 to 8. Designate the hand condition (WRKDAT 1 to 8) No. for which the weight 
and size are designated. .

[Reference Program]

1 Oadl On
2 LoadSet 1,1

' Hand 1(HNDDAT1) and workpiece 1(WRKDAT1) conditions.

3 Mov P1
4 Mov P2
5 LoadSet 1,2

' Hand 1(HNDDAT1) and workpiece 2(WRKDAT1) conditions.

6 Mov P1
7 Mov P2
8 Oadl Off

[Explanation]

(1) Set the hand conditions and workpiece conditions used for optimum acceleration/deceleration. This is 

used when setting the optimum acceleration/deceleration for workpiece types having different weights.

(2) The maximum load is set for the hand when the program execution starts.
(3) Set the weight, size (X, Y, Z) and center of gravity position (X, Y, Z) as the hand conditions in parameter 

(HNDDAT 1 to 8).

(4) Set the weight, size (X, Y, Z) and center of gravity position (X, Y, Z) as the workpiece conditions in 

parameter (WRKDAT 1 to 8).

(5) The hand conditions and workpiece conditions changed when this command is executed are reset to the 

system default value when the program is reset and when the End statement is executed.
As the system default values, the hand conditions are set to the rated load, and the workpiece condi-
tions are set to none (0kg).

(6) Refer to 

Page 496, "5.16 Hand and Workpiece Conditions (optimum acceleration/deceleration settings)"

 

for details on the optimum acceleration/deceleration. 
Refer to 

Page 523, "5.24 Interference avoidance function"

 for details of the interference avoidance 

function.

[Related instructions]

Oadl (Optimal Acceleration)

, 

HOpen / HClose (Hand Open/Hand Close)

[Related parameter]

HNDDAT1 to 8, WRKDAT1 to 8, HNDHOLD1 to 8
Refer to 

Page 496, "5.16 Hand and Workpiece Conditions (optimum acceleration/deceleration settings)"

.

Refer to 

Page 438, "Table 5-1: List Movement parameter"

 for the ACCMODE. 

Refer to 

Page 523, "5.24 Interference avoidance function"

 for details of the parameter about interference 

avoidance function.

LoadSet[]<Hand condition No.>, <Workpiece condition No.>

Содержание CR750 Series



























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды