11
GB
D
F
I
NL
E
P
GR
RU
TR
Product name
External
output
signal lines
Display
lamps etc.
Model and specifications
Use plastic-sheathed cord or cable.
Wiring type: CV, CVS, or equivalent.
Wiring size: Twisted 0.5 mm
2
- 1.25 mm
2
Single wire: ø0.65 mm - ø1.2 mm
No-voltage “a” contacts
DC30 V 1 A or less
AC100 V or AC200 V 1 A or less
Product name
External
input signal
lines
Switches
Model and specifications
Use plastic-sheathed cord or cable.
Wiring type: CV, CVS, or equivalent.
Wiring size: Twisted 0.5 mm
2
- 1.25 mm
2
Single wire: ø0.65 mm - ø1.2 mm
No-voltage contacts
External input functions
8. Remote Controller Operation Problems and Solutions
Cause
• Power failure of indoor unit
• Power failure of outdoor unit
• Over connection of MA remote controller (Max. 2 remo-con)
• Transmission line connects to TB7 of outdoor unit (Should be
connected to TB3)
• MA remo-con connects to TB5 of indoor unit (Should be con-
nected to TB15)
• MA remo-con line is shorted or broken.
• Power supply line or transmission line is shorted or broken.
• Blow out fuse on indoor control board.
• Power failure of outdoor unit
• MA setting is “Sub”
Main setting: SW1 ON
Sub setting: SW1 OFF
• MA remo-con connects to TB5 of indoor unit (Should be con-
nected to TB15)
• Transmission line connects to TB7 of outdoor unit (Should be
connected to TB3)
• Transmission line is shorted, broken or connection failure.
• Blow out fuse on indoor control board.
• Timer operation with remo-con
• Operation with external I/O controller
Phenomenon
Not appear “
'
” mark on MA remote
controller display (MA dose not re-
ceive the power supply)
Not disappear of “HO”
Appear “
'
” mark but hot operated.
Operates or stops the unit without
push the remo-con button
Description
The power will not be supplied to MA remo-con after finishing the
initial mode correctly.
“HO” is flashing during the initial mode. (Max. 20sec.)
The units cannot operate if transmission line is incorrect.
Wiring Method
1. Check the indoor unit settings (Refer to 7. Electrical Wiring Diagram).
2. When using the external output function, connect the signal lines to the exter-
nal output terminal (TB22) of the unit as appropriate for the application. Peel
the cover of wires and connect to the terminals.
3. When using the external input function, connect the signal lines to the external
input terminal (TB21 or TB23) of the unit as appropriate for the application.
Peel the cover of wires and connect to the terminals.
Caution:
1. TB21 is a dedicated terminal for no-voltage contact input. Connection to
a voltage may result in a fault in the indoor control board.
2. TB23 is a dedicated terminal for voltage contact input. Connect only after
checking polarity. Failure to do so may result in a fault.
3. When using AC100 V or AC200 V, ensure that input wiring and communi-
cation cables are installed separately from output wiring.
4. External signal lines may be extended up to 100 m.
[Fig. 7.5.2]
(P.5)
A
Site wiring
B
Fix low-voltage system (DC30 V or less) wiring with clamps and pass to unit via
transmission line wiring holes.*1
C
Fix high-voltage system (AC100 V or AC200 V) wiring with clamps and pass to
unit via power supply wiring holes.*2
D
To CN51 on control board (air-conditioner internal wiring).
E
model 500 only
F
Low-voltage system clamps
G
Low-voltage system wiring
H
High-voltage system wiring
I
High-voltage system clamps
*1 Installation together with AC100 V or AC200 V high-voltage system wiring may
result in mis-operation of the unit due to noise.
*2 Installation together with DC30 V (or less) low-voltage system wiring may re-
sult in mis-operation of the unit due to noise.
<Arrangement parts on site>
External output functions
