manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric AnyWire ASLINK Скачать руководство пользователя страница 63

7  FUNCTIONS

7.3  Address Inspection Function

61

7

7.3

Address Inspection Function

This function executes an address inspection to detect a slave module having no ID or a slave module having a duplicate ID.

 • If the NZ2AW1GNAL is reset or the power supply is turned off after the no ID setting status and ID 

duplication are detected, the no ID number setting status and ID duplication status cannot be checked until 
automatic address detection and address inspection are performed again. Execute the address automatic 
detection and the address inspection command operations again.

 • If the same ID is set for multiple slave modules, a single ID is stored in Number of the alarm IDs (RWr8) and 

Alarm ID information storage area (5500H to 55FFH). For example, even when multiple modules have an ID 
000AH, "1" is stored in Number of the alarm IDs (RWr8) and "000AH" is stored in Alarm ID information 
storage area (5500H to 55FFH).

 • Even if no ID number is set or the ID is duplicated, bit transmission and word transmission do not stop. 

However, the operation of the NZ2AW1GNAL and slave modules is not guaranteed in the ID duplication 
state.

How to execute the address inspection

1.

Turn on Address inspection command (RY2). Address inspection will start.

2.

Confirm that Address inspection flag (RX15) turns on, and turn off Address inspection command (RY2).

3.

When Address inspection flag (RX15) turns off, the address inspection is completed.

Precautions

An Address inspection cannot be performed in the following cases.
 • Remote READY (RX0) is off.
 • Adjustment mode flag (RXF) is on.
 • Parameter access completion flag (RX11) is off.
 • Automatic address detection is in progress. (Automatic address detection flag (RX14) is on.)
 • Address inspection is in progress. (Address inspection flag (RX15) is on.)
 • When any of the following errors or alarms has occurred

When address inspection is executed, the error information and alarm information are cleared. The error information and 
alarm information to be cleared is the same as when the Error reset request flag (RY0) is turned from off to on.

Page 137 Error reset request flag

Error code, alarm code

Description

0CC9H

DP/DN short error

0CCBH

24V/DP short error

2010H

Non-volatile memory data error (parameter)

2011H

Non-volatile memory data error (IP address)

2400H

IP address setting switch range error

2500H

Module power supply voltage drop error

3000H

Non-volatile memory access error (slave module information)

3C00H

Hardware error

Содержание AnyWire ASLINK









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды