Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 251

Страница: 251 / 366

Voice Networking

Symptom

Possible Cause Corrective Action

Console fails back

to its primary by

queued calls are

lost.

Ensure the Console is connected to the

MiVoice Business.

8.5.2 Voice Mail Resiliency

Table 47: Troubleshooting Voice Mail Resiliency

Voice Mail Type

Symptom

Possible Cause

Corrective Action

A second voice

mailbox has not

been configured

on the secondary

ICP for the resilient

device.

Configure a second voice

mailbox.

Call routing on the

secondary ICP is not

configured to allow

a user to access

the voice mail ports

(by dialing the hunt

group number).

Ensure that call routing is

set up to allow the user

to access the hunt group

number of the voice mail

port.

Embedded

After an IP

phone fails

over to the

secondary,

user cannot

connect to

their voice

mail box.

The centralized 3300

ICP embedded voice

mail controller is out

of service.

Check the 3300 ICP

embedded voice mail

server.

Document Version 1.0

245

Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды