Mitel Inter-Tel Axxess Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 384

Mitel Inter-Tel Axxess Скачать руководство пользователя страница 67

Page 51

Administrator Procedures

Inter-Tel

®

Axxess

®

Administrator Guide — Issue 11.0, May 2008

Freezing/Unfreezing the System History

FREEZING/UNFREEZING THE SYSTEM HISTORY

When certain system failures occur, service personnel might request a “system history freeze.”
This allows them access to the system database so that they can analyze system activity for the
time period preceding the alarm.

To freeze or unfreeze system history:

NOTE:

Do not perform this procedure unless directed to do so by service personnel.

1.

While on-hook, enter the Diagnostics Mode feature code (9900 or 9100) to turn on
diagnostics mode. The display shows DIAGNOSTICS ON.

2.

Enter the Freeze System History feature code (9993 or 9193) or Unfreeze System His-
tory feature code (9998 or 9198). The display shows HISTORY FROZEN (or UNFRO-
ZEN).

If you attempt changing the state of the system history to its current status,

the

display shows HISTORY ALREADY FROZEN (or UNFROZEN).

3.

Enter the Diagnostics Mode feature code (9900 or 9100) to turn off diagnostics mode.
The display shows DIAGNOSTICS OFF.

FREEZING/UNFREEZING THE NETWORK HISTORY

Administrators can freeze or unfreeze the fault history for any node in the network. Service
personnel can then pull the information from each node for troubleshooting purposes. Nodes
are assigned to freeze zones by the database programmer to allow selective freezes. You must
know which zone to freeze/unfreeze and then enter the freeze feature code followed by the
zone number.

A node can be in more than one freeze zone. If you freeze a zone that contains a node that is
already frozen, the display will show “SOME NODES ALREADY FROZEN” and the node
will remain frozen. If you unfreeze a zone with unfrozen nodes in it, the display shows “SOME
NODES ALREADY UNFROZEN.” To determine the individual freeze status of the nodes,
check the message print output.

NOTE:

Do not perform this procedure unless directed to do so by service personnel.

To freeze or unfreeze network history:

1.

While on-hook, enter the Diagnostics Mode feature code (9900 or 9100) to turn on
diagnostics mode. The display shows DIAGNOSTICS ON.

2.

Enter the Network Freeze Zone System Histories feature code (9939 or 9139) or Net-
work Unfreeze Zone System Histories feature code (9989 or 9189). Display shows
SELECT FRZ ZONE (0-9) #.

3.

Enter the number of the zone you want to freeze or unfreeze. The display shows
FREEZE ZONE XX IS FROZEN (or UNFROZEN).

If you attempt change the state of

the system history to its current status,

the display shows FREEZE ZONE XX

ALREADY FROZEN (or UNFROZEN).

4.

Enter the Diagnostics Mode feature code (9900 or 9100) to turn off diagnostics mode.
The display shows DIAGNOSTICS OFF.

«
...
65
66
67
68
69
...
»

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов