Mitel Inter-Tel Axxess Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 384

Mitel Inter-Tel Axxess Скачать руководство пользователя страница 64

Page 48

Administrator Procedures

Inter-Tel

®

Axxess

®

Administrator Guide — Issue 11.0, May 2008

Enabling/Disabling the Call Processing Card Modem

Networked systems containing nodes that are running version 8.1 or earlier require special
attention because not all nodes will have an alarm queue. In networks such as this, a broadcast
message is sent only when the most recent network alarm is cleared. When the message is sent,
that network alarm is cleared on all nodes in the system. Once the alarm is cleared, any pre-8.2
nodes will not show any other alarms because these nodes do not have a queue to store alarms.
Nodes that are running 8.2 or later, however, may still have additional alarms in the queue.
When this happens, each 8.2 node must manually clear the other network alarms.

For example, suppose you have a three-node network: node 1 running 8.0; node 2 running 8.2;
and node 3 running 8.2. Node 1 then generates two network alarms, one immediately after the
other. At this point, node 1 shows one network alarm (the latest) and nodes 2 and 3 show two
network alarms. Node 1 then clears the alarm, and a broadcast message is sent. Node 1 now
shows no alarms, but nodes 2 and 3 still show the first alarm. Node 2 then clears the first
alarm, but a broadcast message is NOT sent. Now nodes 1 and 2 show no alarms, but node 3
still has one in the queue. This alarm will stay in the queue until node 3 clears it or until the
alarm is overwritten as previously described.

ENABLING/DISABLING THE CALL PROCESSING CARD MODEM

The Call Processing Card (CPC), available in versions 8.0 and later, has a built-in modem that
can be used for a number of functions. Once the modem has been enabled, it can be used for
Database Programming, Message Print, SMDR, and for uploading the system software license.

If disabled, the modem and extension is placed into DND. In DND, the modem rejects all calls
and does not allow camp ons. Any outside calls that attempt to ring a disabled modem are
automatically transferred to the Primary Attendant.

To enable/disable a modem:

NOTE:

Programming off-node modems across an IPRC connection is not supported.

1.

While on-hook, enter the Modem Enable (9866) or Modem Disable (9867) feature
code. The display shows ENABLE (DISABLE) MODEM EXT #.

2.

Enter the extension of the modem (local or off-node) to enable/disable. The display
shows MODEM ENABLED (DISABLED).

NOTE:

If an invalid modem extension is entered, the display shows INVALID MODEM

EXTENSION.

ASSIGNING THE CPC MODEM TO A DSS/BLF BUTTON

To easily monitor the CPC modem, program a Direct Station Selection/Busy Lamp Field (DSS/
BLF) button to reflect the modem’s status (see

). When programmed for a local or off-

node CPC modem, the DSS/BLF button indicates the following states:

•

Unlit:

Modem is not active.

•

Fast Flash:

Modem is ringing.

•

Slow Flash:

Modem is disabled.

•

Solid:

Modem is connected to a call.

«
...
62
63
64
65
66
...
»

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов