manualshive.com logo in svg

Mitel Inter-Tel Axxess, Руководство администратора, Страница: 33 / 384

Поделиться
Скачать
Mitel Inter-Tel Axxess Скачать руководство пользователя страница 33

Page 17

Administrator Procedures

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Programming the Database Using an Administrator’s Station

Entry to the Database Programming feature at the Administrator station can be protected using
a password. A password prevents unauthorized users from altering the system database.

 

NOTE:  

Passwords are very important to system security. Without sufficient password protec-

tion, the telephone system database is vulnerable to unauthorized access.

Depending on the database changes you make, the system may require a reset after program-
ming. If so, the system will prompt you for a reset and ask if it should be done immediately or
delayed. Delaying the reset may prevent interruption in service. However, if a reset is required
it should be done as soon as possible to permit proper system operation.

 

NOTE:  

A system reset will drop all calls in progress.

Entering Alphanumeric Information: 

When entering alphanumeric information, such as a username, reminder message, or Do-Not-
Disturb message, press 

 or 

USE ALPHA MODE

/

USE NUMERIC MODE

 menu but-

ton to switch back and forth between alphanumeric and numeric mode.

•

In numeric mode,

 the dialpad buttons are used to enter numbers 0-9, the pound (

)

button is used for entering a hyphen (-), and the asterisk (

) button is used for entering

a colon (:). For example, 1

00 would enter “1:00” in numeric mode.

•

In alphanumeric mode,

 dialpad buttons are used to enter the desired letters, numbers,

and punctuation. The number of times a button is pressed determines which character is
entered. For example, 533266 would enter “JEAN” in English. When adjoining charac-
ters are located under the same button, press 

 to advance to the next character.

For example, 66

 

 6667776 would enter “NORM.” 

•

Refer to the table on the following page to program information in alphanumeric mode.
(Note that letters correspond to the letters printed on dialpad buttons.) Japanese charac-
ters will be available only if the Multilingual premium feature is included in your soft-
ware license. Japanese is programmed as a Primary or Secondary Language, and the
Administrator’s station is set for Japanese.

MSG

#

FWD

FWD

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов