manualshive.com logo in svg

Mitel Inter-Tel Axxess, Руководство администратора, Страница: 29 / 384

Поделиться
Скачать
Mitel Inter-Tel Axxess Скачать руководство пользователя страница 29

Page 13

Administrator Procedures

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

System Administrator Procedures

SYSTEM ADMINISTRATOR PROCEDURES

If your endpoint is designated as a system administrator endpoint, you can perform the follow-
ing procedures:

•

Place the local node or other nodes in the network in night or day mode

•

Set the date and time of the local node

•

Set the network date and time and re-synchronize clocks in the network

•

Make database changes (see 

page 16

 for a list of programming areas)

•

Enable, disable, and reset local and off-node Call Processing Card modems

•

Program system speed-dial numbers on the local node

•

Receive and clear displayed system and network alarms

•

Use diagnostic mode features:

—

Freeze and unfreeze the database history for the local node or any node in the net-
work using programmed freeze zones

—

Print error logs

—

Seize specific devices for troubleshooting purposes

PLACING THE SYSTEM IN NIGHT MODE

An Administrator station can place the local node in day or night mode. The day/night mode
determines which lists the system will use for trunk access, toll restriction, etc.

To turn night mode on or off:

While on-hook, enter the Night Ring On/Off feature code (9860). You hear a single
confirmation tone.

 

The display shows NIGHT MODE IS ON (or OFF). Then, if night

mode was turned on, the display shows THE SYSTEM IS IN NIGHT MODE until day
mode is turned on.

PLACING NODES IN DAY OR NIGHT MODE

An Administrator station can place one or more nodes in day or night mode. The day/night
mode determines which lists the system will use for trunk access, toll restriction, etc.

The network determines the day/night mode status of a call based on the day/night mode status
of the node where the trunk resides.

To turn night mode on:

1. 

While on-hook, enter the Enable Network Night feature code (9861). 

2. 

You are prompted to enter a node number. Enter 01-99 for the desired node number. To
select all nodes, enter 00.

3. 

You hear a single confirmation tone.

 

The display shows NIGHT MODE IS ON. Then

the display shows NODE X IS IN NIGHT MODE until day mode is turned on.

To turn day mode on:

1. 

While on-hook, enter the Enable Network Day feature code (9862). 

2. 

You are prompted to enter a node number. Enter the desired node number.

3. 

You hear a single confirmation tone.

 

The display shows DAY MODE IS ON.

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов