manualshive.com logo in svg

Mitel Inter-Tel Axxess, Руководство администратора, Страница: 281 / 384

Поделиться
Скачать
Mitel Inter-Tel Axxess Скачать руководство пользователя страница 281

Page  265

Remove from Paging

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0,

 

May 2008

REMOVE FROM PAGING

An Inter-Tel endpoint user can prevent the endpoint from receiving pages or allow it to receive
pages again using these feature codes. If the endpoint is assigned to more than one page zone,
all zones are removed or replaced; the user cannot toggle individual zones.

To enable/disable zone pages:

1. 

While on- or off-hook, enter the Page Receive On/Off feature code (325) to prevent the
endpoint from receiving pages. You hear a confirmation tone and the display shows
PAGE RECEIVE ON (or OFF).

2. 

If off-hook, hang up.

DO-NOT-DISTURB

Placing a station in Do-Not-Disturb halts all pages, incoming intercom calls, camped-on calls,
and transferred calls to that station. Queue callbacks, recalls, and direct ring-in calls are not
blocked. Another user calling the station while it is in Do-Not-Disturb hears a repeating signal
of four fast tones and a pause (display endpoints show the Do-Not-Disturb message); the user
cannot camp on, but can queue or leave a message at the station. 

NOTE:  

Direct ring-in calls forwarded to a station in DND will ring according to the DND rules.

If desired, individual stations can be prevented from using Do-Not-Disturb by disabling the
Do-Not-Disturb option in the database. 

If a hunt group station is in Do-Not-Disturb, calls to the user’s hunt group do not cause the
endpoint to ring, but the individual trunk button will flash if all other stations in the hunt group
are busy, forwarded, have hunt group remove enabled, or are in Do-Not-Disturb. Hunt group
announcement stations and overflow stations can use Do-Not-Disturb to block hunt group calls
by using Do-Not-Disturb.

Inter-Tel endpoints may be given Do-Not-Disturb override permission. These stations, when
reaching a station in Do-Not-Disturb, can enter the Do-Not-Disturb Override feature code
(373) to place a non-handsfree intercom call to the station. Single-line stations cannot be
enabled to use the Do-Not-Disturb Override feature.

When a station is placed in DND, the user may select one of 20 system-stored messages that
will appear on the top line of the display (unless Do-Not-Disturb is enabled while the user is on
a call or off-hook, in which case message 1 is automatically selected). When a station in Do-
Not-Disturb is called by a display endpoint user, the caller sees the selected message. 

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов