manualshive.com logo in svg

Mitel Inter-Tel Axxess, Руководство администратора, Страница: 182 / 384

Поделиться
Скачать
Mitel Inter-Tel Axxess Скачать руководство пользователя страница 182

Page  166

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Emergency Outgoing Access Lists

•

If the user accesses ARS and dials any Emergency Number (1-10):

 

a.

The call is routed to Route Group 1.

b.

The call tries the first facility group in Route Group 1.

c.

The trunk group or node trunk group validates the station originating the emer-
gency call against the group’s Emergency Day/Night Outgoing Access List. 

d.

If the call is denied,

 the call tries the next member in the facility group. If each

member denies the call, the call tries the next facility group in Route Group 1’s
list. 

If everything is denied due to Emergency Outgoing Access,

 the call is routed once

again to Route Group 1. The call then tries the first facility group in Route Group
1. The trunk group or node trunk group does 

not

 validate the station originating

the emergency call against the group’s Emergency Day/Night Outgoing Access
List. If no trunks are available, the call tries the next member in the facility group.
If all of the members are unavailable, the call camps-on to Route Group 1 until a
trunk is available. 

NOTE:  

Inter-Tel highly recommends that only local trunks be installed and used for

emergency trunk access and that only local trunks be programmed in Route Group 1.
Programming a node in Route Group 1 may cause the system to access a trunk on a
separate node when ARS is used for emergency access. If this occurs, Emergency Out-
going Access is no longer validated.

The system will allow the Dialing Wait After Connect timer to expire and will then dial the
digit string programmed in the database as the emergency number. 

At the time the call is processed, a minor alarm will be generated by the system and sent to all
administrator stations. Also if the Message Print option is enabled, the alarm message is sent to
the designated output port.

Emergency Outgoing Access Lists

As of version 7.0, the system supports two outgoing access lists called 

Emergency Day Outgo-

ing Access

 and 

Emergency Night Outgoing Access

. These lists, which are similar to the Day/

Night Outgoing Access lists, are programmable for CO Trunk Groups and Node IP Connection
Groups. These lists default to the Auto Extension List 

PP051: Auto: All Stations

.

EMERGENCY CALL FEATURE

AXXESS DATABASE:

Station user

dials 911

EMERGENCY EXT. =
TRUNK GROUP 1 (92001)

EMERGENCY No. = 911

CALL PLACED
TO 911

ALARM #11
DISPLAYED

MESSAGE PRINTOUT,

IF ENABLED

OR

DIRECT TRUNK ACCESS

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов