Mitel DBC 223 Скачать руководство пользователя страница 95

Страница: 95 / 121

OICE

4223 O

FFICE

(DBC 223)

FOR

OICE

MX-ONE

3/1553-ANF 901 54 Uen F5 2018-12-03

9.14.2.2

To answer a call

The incoming call can be answered by any telephone (where the number is multiple

represented as a key and there is one of Line 1 or Line 2 idle for answering calls) by

lifting the handset and pressing that key. After pressing the line-key the call will be auto

matically transferred to an idle Line 1 or Line 2. After the answer, that telephone will be

in speech with the calling party and all the other telephones having the number multiple

represented will be idle (they can receive new calls).

9.14.2.3

To make a call

Any telephone that has a key that represents another number can use that key to

initiate a call by pressing the key when there is no incoming call on that line. The

number initiated on this key will be redialed as for Dial-by-Function key ( 4.8.3

Dial-by-Function key on page 53 ).

9.15

NIGHT SERVICE

During night service, incoming external calls are transferred to any selected extension

or group of extensions.

9.15.1

NIGHT SERVICE COMMON

All incoming calls are routed to one extension, and calls are answered in the normal

way.

9.15.2

NIGHT SERVICE INDIVIDUAL

One or more of the external lines in the exchange are routed to the designated exten

sion, and calls are answered in the normal way.

9.15.3

NIGHT SERVICE UNIVERSAL

All incoming calls are signaled on universal signaling devices, that is, a bell. In order to

answer the call use the following procedure:
•

Lift the handset (dial tone).

•

Press the soft-key

GrpPickUp

or dial 8.

9.15.4

NIGHT SERVICE FLEXIBLE

Flexible night service permits you to select an external line and connect it directly to

Line 1, 2 or an additional line on your telephone. This is convenient when you are

expecting important calls after office hours and you wish to get them without delay.

Details about external line numbers can be obtained from the PBX operator. The

following procedures are used:

To activate flexible night service

•

Lift the handset (dial tone).

•

Dial *84*route number*external line number#.

•

Replace the handset.

Содержание DBC 223


























































































































Результаты поиска

Содержание DBC 223

Отзывы:

Mitel DBC 223, Инструкция по применению, Страница: 95 / 121

Результаты поиска

Содержание DBC 223

Отзывы: