Mitel DBC 223 Скачать руководство пользователя страница 79

Страница: 79 / 121

OICE

4223 O

FFICE

(DBC 223)

FOR

OICE

MX-ONE

3/1553-ANF 901 54 Uen F5 2018-12-03

MESSAGES

7.1

INTEGRATED VOICE MAIL

Note:

Not applicable

7.2

MANUAL MESSAGE WAITING, MMW

7.2.1

MANUAL MESSAGE WAITING INDICATION

A function key with a lamp on a digital system telephone can be initiated as a manual

message waiting key (MMW-key).
If there is a message waiting, the corresponding lamp will be ON and you will hear a

special dial tone after lifting the handset.

7.2.2

CALLING THE PARTY THAT REQUESTED MANUAL MESSAGE

WAITING

•

Press the MMW-key that is ON and a call is initiated to the number that requested

message waiting. The lamp is turned OFF after answer.

7.2.3

CHECKING THE PARTY THAT REQUESTED MANUAL MESSAGE

WAITING

•

Press the soft-key

Program

(all lamps turns OFF).

•

Press the MMW-key (the display indicates the number that requested message

waiting).

•

Press the soft-key

Exit

7.2.4

ORDER MANUAL MESSAGE WAITING INDICATION

To order manual message waiting to another extension

•

Lift the handset (dial tone).

•

Dial *31*extension number#.

•

Replace the handset.

7.2.5

CANCEL MANUAL MESSAGE WAITING INDICATION

To cancel manual message waiting to another extension

•

Lift the handset (dial tone).

•

Dial #31*extension number#.

•

Replace the handset.

To cancel manual message waiting at own extension

Содержание DBC 223


























































































































Результаты поиска

Содержание DBC 223

Отзывы:

Mitel DBC 223, Инструкция по применению, Страница: 79 / 121

Результаты поиска

Содержание DBC 223

Отзывы: