Mitel DBC 223 Скачать руководство пользователя страница 72

Страница: 72 / 121

3/1553-ANF 901 54 Uen F5 2018-12-03

ALL

FORWARDING

•

Lift the handset (dial tone).

•

Dial

* 22 * extension number to divert

•

Dial

route access code and the external number

•

Replace the handset.

6.3.4

CANCELING EXTERNAL FOLLOW-ME REMOTELY

Follow the steps below to terminate External follow-me for another extension:
•

Lift the handset (dial tone).

•

Dial

# 22 * diverted extension number #

•

Replace the handset.

6.4

PERSONAL NUMBER

6.4.1

GENERAL

This section describes the user procedures for handling the personal number feature.

Every personal number can have up to 5 profiles. You can activate or deactivate them

by using the Personal Number key, or by dialing a procedure. The latter can be done:
•

From your own telephone assigned to the personal number, PN.

•

From the operator assistant.

No matter which method is used, the current active profile is shown in the display of

your own telephone. If no profile is active, the display shows the normal idle state.
However, if the Boss-secretary service is initiated, PN profile1 is reserved. This results

in limiting the number of PN profiles to four (profiles 2,3,4 and 5). The Boss-secretary

service can be activated and deactivated by both the boss and secretaries by dialing a

procedure. The feature can also be deactivated by the system administrator. When the

Boss-secretary service is active, active profile1 is shown in the display of boss tele

phone, and Personal number key LED lights on both the boss’s and the secretaries’

telephones. If the Boss-secretary service is inactive, the display shows the normal idle

state.

6.4.2

PROCEDURES

The value of Profile is 1 to 5.
PN indicates the personal number of the extension with the facility available. In most

cases the personal number is the same number as your directory number.

Содержание DBC 223


























































































































Результаты поиска

Содержание DBC 223

Отзывы:

Mitel DBC 223, Инструкция по применению, Страница: 72 / 121

Результаты поиска

Содержание DBC 223

Отзывы: