manualshive.com logo in svg

Mitel DBC 223, Инструкция по применению, Страница: 55 / 121

Поделиться
Скачать
Mitel DBC 223 Скачать руководство пользователя страница 55

M

I

V

OICE

 4223 O

FFICE

 (DBC 223) 

FOR

 M

I

V

OICE

 MX-ONE

55

3/1553-ANF 901 54 Uen F5 2018-12-03

5.2 

CONFERENCE

You can establish speech connections with up to seven parties. Only the conference 

leader (that is, the person initiating the conference call) can invoke participants.

Note:  

The conference tone can by categorization be disabled.

The following is an example of display information when you are the conference leader:

The following is an example of display information when you are a conference member:

5.2.1 

TO INITIATE A CONFERENCE

•

A call to the first party is established on Line 1-key.

•

Press the soft-key 

Conf/Transf

 , the Inquiry-key, or the Line 2-key.

•

Dial the second party's extension number (inform about the conference).

•

Press the soft-key 

Conference

  or the Conference-key or dial 3.

During the conference, conference tone will be heard.

5.2.2 

TO ADD A NEW PARTY IN A CONFERENCE

•

Press the soft-key 

AddMember

 , the Inquiry-key, or Line 1 or Line 2.

•

Dial the new party's extension number (inform about the conference).

•

Press the soft-key 

Conference

 or the Conference-key or dial 3.

5.2.3 

INTERNAL CONSULTING DURING A CONFERENCE

As conference leader you can make an Inquiry call to one of the conference members.
Doing this you will get busy tone and to reach the person in question you must use the 

Intrusion procedure, 5.5 Intrusion on page 57 .
•

Press the Inquiry key (dial tone).

Содержание DBC 223


























































































































Отзывы:

Нет отзывов