Mitel DBC 223 Скачать руководство пользователя страница 23

Страница: 23 / 121

OICE

4223 O

FFICE

(DBC 223)

FOR

OICE

MX-ONE

3/1553-ANF 901 54 Uen F5 2018-12-03

After transferring the ongoing call

•

Press the Inquiry-key.

•

Dial the extension number or the external number.

•

Press the soft-key

Transfer

(the ongoing call is transferred).

•

Press the Line 2-key to answer.

3.4

DO NOT DISTURB, DND

This feature is used to prevent incoming calls from being indicated in a telephone.

However, you can still use the telephone for outgoing calls as usual.
The calling party receives a number unobtainable tone and a display message giving

information about this feature.

3.4.1

TO ORDER DO NOT DISTURB

Using the soft-key Absence

•

Press the soft-key

Absence

•

From the menu select

Do not Disturb

option.

•

Press the soft-key

Activate

(DND lamp is turned ON).

Using DND-key

•

Press the soft-key

NotDisturb

or the DND-key (the DND lamp is turned ON if

exists).

Using a procedure

•

Lift the handset (dial tone).

•

Dial *27# (DND the lamp is turned ON).

•

Replace the handset.

Note:

For an additional line, the DND lamp is not affected, but the ADN LED itself will

flash.

3.4.2

TO CANCEL DO NOT DISTURB

Using the soft-key Absence

•

Press the soft-key

Absence

•

From the menu select

Do not Disturb

•

Press the soft-key

Deactivate (DND lamp is turned OFF).

Using DND-key

•

Press the DND-key or the soft-key

NotDisturb

(the DND lamp is turned OFF if

exists).

Using a procedure

•

Lift the handset (special dial tone).

•

Dial #27# (dial tone and the DND lamp is turned OFF).

•

Replace the handset.

Содержание DBC 223


























































































































Результаты поиска

Содержание DBC 223

Отзывы:

Mitel DBC 223, Инструкция по применению, Страница: 23 / 121

Результаты поиска

Содержание DBC 223

Отзывы: