MITECH MT660 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 25

MITECH MT660 Скачать руководство пользователя страница 16

mvip@mitech-ndt.com

change and exit

5.9 Changing Resolution

The

gauge

has

selectable

display

resolution, which is 0.1mm

and 0.01mm.

When the resolution is set to 0.01mm, the tested piece surface should be smooth to get

accurate test result. When measuring rough surface or coarse grained materials, it is suggested to
use low resolution.

5.10 Memory Management

5.10.1 Store a Record

By simply pressing the

key after a new measurement reading appears, the measured

thickness value will be saved to current selected data group. It is added as the last record of the
group.

5.10.2 View the Saved Record

This function provides the user with the ability to view the records in a desired data group

previously saved in memory. Following is the steps:

Activate the Memory

Manager dialog as right

figure.

Press

to move the

cursor; Press

or F3 key

to open the View Record

Data dialog, see next

figure.

Press

to move the

cursor

to

the

desired

record.

Press F3 to delete the

focused record.

Press F2 to clear all the

records of this group.

Press

/F1 to exit.

5.10.3 Select As Current Data Group

There are 100 data groups (F00 ~ F99) inside the gauge that can be used to store the

measurement values. At most 100 records (thickness values) can be stored to each group. You
can change the destination data group to store the measured values as following.

[email protected]

«
...
14
15
16
17
18
...
»

Содержание MT660


























Отзывы:

Нет отзывов