MITECH MT660 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 25

MITECH MT660 Скачать руководство пользователя страница 10

mvip@mitech-ndt.com

screws. To insert the batteries:
1. Loosen the two screws of the battery cover.
2. Lift the cover off upward.
3. Insert the batteries into the battery compartment.
4. Close the battery compartment and fasten the screws.
5. Turn on the instrument to make sure the battery is installed correctly and firmly.

4.2 Connecting the Probe

To prepare the instrument for operation, you have to connect a probe to it. The instrument is

available with the Lemo socket connectors.

When connecting a probe to the instrument, it’s not only important that the physical connection

be properly made. It’s also important that the instrument is properly configured to work with the
installed probe.

4.3 Starting the Instrument

To start the instrument, press down

until display activates. While the device is booting a

splash screen, the serial number of the unit, the installed software version, the date and time of the
system appear on the display.

The start display of the

instrument appears as right

figure.

Press F1 key to change to

a different language.

Press F3 key to skip the

booting check process and

enter the measure mode

immediately.

The instrument carries out

a

self-check

and

then

switches over to the measure

mode automatically if there is

no key operation.

The instrument is now

ready

for

the

first

measurement.

The instrument will automatically reload last settings. It has a special memory that retains all of

its settings even when the power is off.

To shut off the instrument, keep pressing down

key until shutting down message appears.

The gauge also has auto power off function to save battery capacity. If there is no operation

during a specified period of time (setting as the Auto Poweroff delay), the gauge will be powered
off automatically.

Note: The instrument will shut off automatically if the battery capacity level is too low.

4.4 Configuration of the Standby Settings

To save battery power, the device supports the following power states:

Run state

– The main unit is running at full frequency

Standby state

– After 5 seconds (default setting) the brightness of the LCD display is tuned to a

low level and the CPU is running at reduced frequency. This has no effects on the data or the
memories. Pressing any key or performing a measurement sets the unit back to run state and the
brightness is tuned back.

Power off state

– After 2 minutes (default setting) the instrument changes from standby state to

[email protected]

«
...
8
9
10
11
12
...
»

Содержание MT660


























Отзывы:

Нет отзывов