Mipex MIPEX-02 Series Скачать руководство пользователя страница 38

Страница: 38 / 46

Optosense LLC

USER MANUAL

Design department

SMALL-SIZE EXPLOSIVE GAS MEASURING

SENSOR MIPEX-02-X-X-X.1 X (RX)

ESAT.413347.005 UM

Revision 3.0

January 19th, 2017

Page 38 of 46

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED.

Appendix C.2.5. Commands for configuring net address

Request syntax

USER

mode

OEM

mode

Response description

Command description

!**

yes

4 bytes in ASCII format

: “0D”

symbol,

sensor’s hexadeci-

mal net address in range
00…FF and “0D” symbol.

Returns sensor’s net address

%AABB

yes

Three bytes in ASCII format:
sensor’s new hexadecimal
net

address

and

“0D”

symbol.

Intended to assign a new net
address

to sensor with

address

NETOFF

yes

NETOFF OK

NETOFF FAULT

Cancels storing of sensor’s net
address  in  sensor  memory.
After  sensor  receives  this
command  and  sensor  power
resets

, sensor’s net address

becomes “00”.

NETON

yes

NETON OK

NETON FAULT

Allows assigning and storing
sensor’s net address by using
<%AABB> command.

Appendix C.2.6. Commands for controlling power consumption mode

Request syntax

USER

mode

OEM

mode

Response description

Command description

LOWPWX

yes

LOWPWX OK

LOWPWX FAULT

Intended for controlling power
consumption mode.

stands

for

mode

number

corresponds to normal mode,
1 corresponds to low power
consumption mode).

LOWPW?

yes

2 bytes in ASCII format and
“0D” symbol: “HI” – standard
mode

; “LW” – low power con-

sumption mode.

Returns active power con-
sumption mode.

Содержание MIPEX-02 Series















































Результаты поиска

Содержание MIPEX-02 Series

Отзывы:

Mipex MIPEX-02 Series, Руководство пользователя, Страница: 38 / 46

Результаты поиска

Содержание MIPEX-02 Series

Отзывы: