Mipex MIPEX-02 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 46

Mipex MIPEX-02 Series Скачать руководство пользователя страница 35

Optosense LLC

USER MANUAL

Design department

SMALL-SIZE EXPLOSIVE GAS MEASURING

SENSOR MIPEX-02-X-X-X.1 X (RX)

ESAT.413347.005 UM

Revision 3.0

January 19th, 2017

Page 35 of 46

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED.

Appendix C.2.4. Commands for sensor configuring and span calibrating

Request syntax

USER

mode

OEM

mode

Response description

Command description

AZERO?

no

yes

AZERO ON

or

AZERO OFF

Intended for checking current auto-
zeroing

algorithm

status

(this

algorithm must not be used on CO

2

sensors).

AZERO OFF

no

yes

AZERO OFF

Turns off the auto-zeroing algorithm.

AZERO ON

no

yes

AZERO ON

Turns on the auto-zeroing algorithm
(this algorithm must not be used on
CO

2

sensors).

CALB AAAA

no

yes

CALB AAAA OK

or

CALB AAAA FAULT

This command is used for gas span
calibration, where

AAAA

is a CGM

concentration value in % vol. × 100.
For example,

AAAA

= 0198 corre-

sponds to 1.98 % vol. See Appendix
D.1 for detailed procedure descrip-
tion.

CALB1 XXXXX

no

yes

CALB1 XXXXX OK

or

CALB1 XXXXX FAULT

Writes scale coefficient for sensor
calibration range of 0…5 % vol.

XXXXX

is the coefficient value incre-

mented  to  10000  (for  example:  to
write  the  scale  coefficient  of  0.009
send  <CALB2  00090>).  This  com-
mand can be used to recalibrate sen-
sor  if  scale  coefficient  is  known.  The
scale  coefficients  for  different  gases
are  individual  for  each  sensor.  To
achieve  cross-coefficients  contact
support.

CALB2 YYYYY

no

yes

CALB2 YYYYY OK

or

CALB2 YYYYY FAULT

Writes scale coefficient for sensor
calibration range of 5…100 % vol.

YYYYY

is the coefficient value incre-

mented  to  10000  (for  example:  to
store  the  scale  coefficient  of  0.01
send  <CALB2  00100>).  This  com-
mand can be used to recalibrate sen-
sor  if  scale  coefficient  is  known.  The
scale  coefficients  for  different  gases
are  individual  for  each  sensor.  To
achieve  cross-coefficients  contact
support.

CALB3 ZZZZZ

no

yes

CALB3 ZZZZZ OK

or

CALB3 ZZZZZ FAULT

Writes scale coefficient for the whole
sensor cal

ibration range (0…100%

vol.).

ZZZZZ

is the coefficient value

incremented to 10000 (for example:
to store the scale coefficient of 0.7
send

<CALB3

07000>).

This

command  can  be  used  to  recalibrate
sensor  if  scale  coefficient  is  known.
The  scale  coefficients  for  different
gases are individual for each sensor.
To achieve cross-coefficients contact
support.

«
...
33
34
35
36
37
...
»

Содержание MIPEX-02 Series















































Отзывы:

Нет отзывов