background image

29 

9. Limited Product Warranty 

 

 

Para Systems, Inc. (Para Systems) warrants this equipment, when properly applied and operated within 
specified conditions, against faulty materials (excluding the batteries) or workmanship for a period of 
three years from the date of purchase.  Para Systems Inc. (Para Systems) warrants the batteries for a 
period of two years from the date of purchase.  For equipment sites within the United States and 
Canada, this warranty covers depot repair or replacement of defective equipment at the discretion of 
Para Systems.  Depot repair will be from the nearest authorized service center.  The customer pays for 
shipping the product to Para Systems.  Para Systems pays ground freight to ship the product back to the 
customer.  Replacement parts and warranty labor will be borne by Para Systems.  For equipment located 
outside of the United States and Canada, Para Systems only covers faulty parts.  Para Systems products 
that are depot repaired or replaced pursuant to this warranty shall only be warranted for the unexpired 
portion of the warranty applying to the original product.  This warranty applies only to the original 
purchaser who must have properly registered the product within 10 days of purchase. 
 
The warranty shall be void if (a) the equipment is damaged by the customer, is improperly used, is 
subjected to an adverse operating environment, or is operated outside the limits of its electrical 
specifications; (b) the equipment is repaired or modified by anyone other than Para Systems or Para 
Systems approved personnel; or (c) has been used in a manner contrary to the product’s User's Manual 
or other written instructions. 
 
Any technical advice furnished before or after delivery in regard to use or application of Para Systems’ 
equipment is furnished without charge and on the basis that it represents Para Systems’ best judgment 
under the circumstances, but it is used at the recipient’s sole risk. 
 
EXCEPT AS PROVIDED HEREIN, PARA SYSTEMS MAKES NO WARRANTIES, EXPRESSED OR 
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE.  Some states do not permit limitation of implied warranties; therefore, the aforesaid 
limitation(s) may not apply to the purchaser. 
 
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL PARA SYSTEMS BE LIABLE FOR DIRECT, 
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE 
OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  Specifically, Para 
Systems is not liable for any costs, such as; labor for on-site installation, on-site maintenance or on-site 
service, lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of 
data, cost of substitutes, claims by third parties, or otherwise.  The sole and exclusive remedy for breach 
of any warranty, expressed or implied, concerning Para Systems’ products and the only obligation of 
Para Systems hereunder, shall be depot repair or replacement of defective equipment, components, or 
parts; or, at Para Systems’ option, refund of the purchase price or substitution with an equivalent 
replacement product.  This warranty gives you specific legal rights and you may also have other rights 
which vary from state to state. 
 
No employee, salesman, or agent of Para Systems is authorized to add to or vary the terms of this 
warranty. 

 
 
 
 
 
 

PN: 34000497 R1

Содержание RPM1581EV6































Отзывы: