Minuteman RPM1581EV6 Скачать руководство пользователя

Страница: 3 / 30

1. IMPORTANT SAFETY INSTRUCTIONS

This manual contains important instructions that should be followed during the installation and the
operation of the Remote Power Manager (RPM).

SAVE THESE INSTRUCTIONS

An Important Notice



To ensure safety a

Qualified Service Personnel

should perform the installation.



Make sure that the AC Utility outlet is properly grounded.



Do not open the unit there are no user serviceable parts inside. Servicing of RPM should be

performed by Qualified Service Personnel Only.



Please make sure that the input voltage of the RPM matches the supply voltage.



Make sure the RPM is installed in the proper environment as specified.



This RPM series is

ONLY

intended to be installed in an indoor temperature controlled environment

that is free of conductive contaminants.



Do not operate the RPM in: extremely dusty and/or unclean areas, locations near heating devices,

water or excessive humidity, or where the RPM is exposed to direct sunlight.



Select a location, which will provide good air circulation for the RPM at all times.



CAUTION

– To reduce the risk of fire, connect only to a branch circuit with over current protection in

accordance with the National Electric Code.



CAUTION

- Connect the RPM to a two pole, three wire grounding AC wall outlet. The receptacle

must be connected to the appropriate branch protection (circuit breaker or fuse). Connection to any
other type of receptacle may result in a shock hazard and violate local electrical codes. Do not use
extension cords, adapter plugs, or surge strips.



Route power cords so they cannot be walked on or damaged.



CAUTION

- To reduce the risk of electrical shock with the installation of this RPM equipment and the

connected equipment, the user must ensure that the combined sum of the AC leakage current does
not exceed 3.5mA.



CAUTION

- To de-energize the outputs of the RPM: Disconnect the RPM from the AC wall outlet.



CAUTION

- Do not install this device if there is not at least 30 feet (10 meters) or more of wire

between the electrical outlet and the electrical service panel.

Содержание RPM1581EV6































Результаты поиска

Содержание RPM1581EV6

Отзывы:

Похожие инструкции для RPM1581EV6

Бренды по названию

Популярные бренды

Minuteman RPM1581EV6, Руководство пользователя

Результаты поиска

Содержание RPM1581EV6

Отзывы:

Похожие инструкции для RPM1581EV6

Бренды по названию

Популярные бренды