19
18
WEAK/BAD/DISCONNECTED BATTERY
The UPS automatically tests the battery’s condition. If the battery is weak, bad or
disconnected, the Weak/Bad/Disconnected Battery icon will illuminate and the alarm
will beep three times every five-minutes until the battery is reconnected, replaced or
passes a self test. It is recommended that the UPS be allowed to charge overnight
before performing a battery test to confirm a Weak/Bad Battery condition.
OVERLOAD
When the amount of load attached to the UPS is > 106% of its power rating; the
Overload icon will flash Off and On, all of the LEDs in the Load Level Bar Graph will
be illuminated and the audible alarm will beep continuously. This alarm will remain
on until the excess load is removed or the UPS’s self protection circuit shuts the
UPS down. If the UPS shuts down because of an Overload condition, the UPS
must perform an Inverter function or a Self Test to clear the Overload Alarm.
ALARMS
ON BATTERY
When the UPS is operating on the batteries, the On-Battery icon will illuminate and
the audible alarm will sound one beep every ten-seconds. The alarm will stop once
the UPS returns to the AC normal mode.
LOW BATTERY WARNING
When the UPS is operating on the batteries and the battery reserve is running low,
the audible alarm will sound two beeps every five-seconds. This condition will con-
tinue until AC returns or the UPS shuts down from battery exhaustion.
UPS FAULT
When the UPS detects a hardware and/or internal fault, the Fault icon will illuminate
and the audible alarm will beep continuously. The fault condition, in some instances,
may be reset by turning the UPS off and then on again.
POWER MONITORING SOFTWARE
The UPS comes with a Power Monitoring Software CD or you can go to our web
site at www.minutemanups.com/support, then look under Downloads, and then
Software Download Center. Please download (Free of Charge) the latest version
of the Minuteman SentryHD software. See the software CD for the installation of
the Power Monitoring Software.
NOTE: If you are using an External Battery
Pack with this UPS series, the UPS must be configured so that the UPS will
report the correct estimated runtime on the LCD screen and in the Power
Monitoring software and/or the SNMP card. See the Power Monitoring soft-
ware or the SNMP card’s User's Manual to configure the UPS.
NOTE:
The LCD backlight will illuminate for 20-seconds when the UPS switches
to the Battery mode. When the UPS has an event and/or an error code the LCD
backlight will turn on and remain on to alert the user that an event has occurred.
(These items may require optional software or hardware)
Function
Factory
Default
Description
User Choices
Set
inverter
output
voltage
Shut-
down
Type
Set
audible
alarm
state
Enable/
Disable
auto
restart
Battery
life in
days
Battery
install
date
UPS ID Endeavor
Series
Date of
manufac-
ture
1826
Enabled
Enabled
Entire UPS
120VAC
Up to 64 charac-
ters to define the
UPS
Date of battery
replacement -
month/day/year
XX/XX/XXXX
Up to 5
characters
Enable
or
Disable
Enabled, at
low battery,
disabled
Entire UPS or
UPS output
110, 120VAC
At first battery replacement, re-
set to reflect actual number of
days experience in your environ-
ment or leave factory default.
Enter the current date when
replacing batteries.
Use this function to uniquely
identify the UPS in your network
configuration.
Changes output voltage.
Enabled - the UPS will emit a short
beep when in the battery mode.
At Low Battery the UPS will emit
two beeps from low battery warn-
ing until shutdown.
Disabled - Use only when soft-
ware is controlling the UPS or to
silence the alarm.
When enabled, the UPS will
automatically restart from a low
battery shutdown when normal AC
returns.
Enable/
Disable
RPo
Disabled
Enable
or
Disable
Enabled - the UPS will be
powered off and remain off until
the UPS is reset.
Entire UPS - Turns off the entire UPS.
UPS Output - Turns off the UPS's
output receptacles only.
Chapter 5: Configurable Parameters
and Settings
Set
External
Battery
Pack
0
0 - 10
Configures the UPS so that it will
report the correct estimated runt-
ime on the LCD screen and in the
Power Monitoring software and/
or the SNMP card.
Enable/
Disable
ECo
Disabled
Enable
or
Disable
Enabled - the UPS will operate in
the Economy mode.
