Minster IOI, Руководство по обслуживанию

Страница: 34 / 92

D - 9
SUMMARY OF LUBRICATION AREAS
(Refer to “Lubrication Areas” on page D-10 for part locations.)
PART LUBRICATED LUBRICATION INSTRUCTIONS
1. Connection
2. Main Bearings
3. Gibs
4. Ball Box
5. Main Gear Teeth
(Geared Press Only)
6. Driveshaft Bearings
(Geared Press Only)
These parts are lubricated by the recirculating oil lubrication system. Keep the oil
filter clean and check reservoir oil level daily. Oil should appear within 1.50” (38
mm) from the top of reservoir when the pump is not running. With the pump in
operation, oil may be lowered, but must always be within 2.00” (50.8 mm) from
the bottom of the reservoir. Add oil when needed to maintain the proper oil level in
the reservoir. Use an approved lubricant meeting the specifications of Minster
Lubricant No. 1. (Refer to “General Lubrication Specifications For MINSTER
Presses,” Manual No. 507, for a list of approved lubricants and recommended
suppliers.)
Under normal operating conditions, drain the reservoir and refill with new oil after
every 1300 hours of operation.
7. Air Line Lubricator(s)
Check level weekly. Keep lubricator filled with an approved lubricant meeting the
specifications of Minster Lubricant No. 3. (Refer to “General Lubrication Specifica-
tions For MINSTER Presses,” Manual No. 507, for a list of approved lubricants and
recommended suppliers.)
8. Die Cushion
(If Furnished)
A Minster die cushion is lubricated via a one shot lubricator. The lubricator handle
should be pulled once every four (4) hours of operation. Check the lubricator lubri-
cant level daily. Keep the lubricator filled with an approved lubricant meeting the
specifications of Minster Lubricant No. 1. (Refer to “General Lubrication Specifica-
tions For MINSTER Presses,” Manual No. 507, for a list of approved lubricants and
recommended suppliers.) NOTE: A non-Minster die cushion should be lubricated in
accordance the manufacturer’s recommendations.
9. Rotor Seal
Lubricate every three (3) months with an approved grease lubricant meeting the
specifications of Minster Lubricant No. 2. (Refer to “General Lubrication Specifica-
tions For MINSTER Presses,” Manual No. 507, for a list of approved lubricants and
recommended suppliers.)
10. Flywheel Brake
No periodic lubrication required. (If brake is disassembled, apply a thin coating of
Molybdenum Disulfide grease to the inner walls prior to reassembly.)
11. Counterbalance Cylinder
(If Furnished)
Check counterbalance rod oil cup monthly and refill as required. Use an approved
lubricant meeting the specifications of Minster Lubricant No. 1. (Refer to “General
Lubrication Specifications For MINSTER Presses,” Manual No. 507, for a list of
approved lubricants and recommended suppliers.) If internal seals are replaced,
apply a thin coating of Molybdenum Disulfide grease to the inner walls prior to
reassembly.
12. Main Drive Motor
Lubricate in accordance with the motor manufacturer’s recommendations. DO
NOT OVER LUBRICATE.
13. Clutch Flywheel Bearings
Flywheel bearings on Model 101 OBI/OBS presses equipped with Type 26-CFC
clutches and smaller require no periodic lubrication. Flywheel bearings on presses
equipped with Type 28-CFC and larger clutches should be checked every six (6)
months. Bearings on these clutches should be repacked, if required, with an
approved lubricant meeting the specifications of Minster Lubricant No. 2. (Refer to
“General Lubrication Specifications For MINSTER Presses,” Manual No. 507, for a
list of approved lubricants and recommended suppliers.)
14. Inclining Jack
Hand lubricate screw threads monthly with an approved lubricant meeting the speci-
fications of Minster Lubricant No. 1. Lubricate the jack gear box every twelve (12)
months with an approved grease lubricant meeting the specifications of Minster
Lubricant No. 2. (Refer to “General Lubrication Specifications for MINSTER Press-
es,” Manual No. 507, for a list of approved lubricants and recommended suppliers.)