manualshive.com logo in svg

Minolta CF1501, Руководство по обслуживанию

Поделиться
Скачать
Minolta CF1501 Скачать руководство пользователя страница 244

FrameMaker Ver5.5E(PC) CF1501/CF2001 SWITCHES ON PWBs/TECH. REP. SETTINGS
00.11.30

S-13

(2)

Administrator Mode

• The entry on the “Administrator #” set using the Tech. Rep. mode permits the settings of 

the following functions.

1. Administrator Mode Function Setting Procedure

<Procedure>
1. Press the Utility key.
2. Touch the “Administrator Mode” key.
3. Enter the Administrator number from the 10-Key pad.
4. Select the appropriate function.
5. After the settings are complete, touch the “Enter” key to validate the settings.

<Exiting the Mode>
• Press the “OK” key.

2. Administrator Mode Function Tree

✽

Available on the screen when the settings are made for “Mainte. Center” when a Data 
Terminal is mounted.

PRT Area (Top Margin)
PRT Area (Left Margin)
PRT Area (Dup. Left Margin)
Thin Orig.

Expt. User’s 
Mode 1/2

Expt. User’s 
Mode 

Administrator 
Mode 2/2

Administrator 
Mode

Thick Paper and OHP Film
Image Density
Color Shift Correction (C)
Color Shift Correction (M)
Color Shift Correction (Y)
Color Shift Correction (Bk)
Stabilizer

Expt. User’s 
Mode 2/2

Erase

Administrator 
Mode 1/2

Copy Track

Gradation Adjust

Disable Sleep Mode

User Send

Access # Input
Counter Check
Counter Reset
Permission Level
Account Copy Limit set

Содержание CF1501















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды