Minolta CF1501 Скачать руководство пользователя страница 142

Страница: 142 / 270

FrameMaker Ver.5.5E(PC) CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-10

(4)

Removal of the Scanner Motor Drive Board

(5)

Removal of the Flat Cable

1. Remove the IR Rear Upper Cover and IR Rear Cover.
2. Remove the Original Glass.
3. Remove the Scanner Assy.

1. Remove the IR Right Cover, IR Rear Right

Cover, IR Rear Upper Cover, and IR Rear Cover.

2. Remove two screws and the reinforcement

frame.

4004D015AA

3. Unplug three connectors.
4. Remove one screw. Then, remove the Scanner

Motor Drive Board from the PWB support.

4004D016AB

4. Remove two screws, unplug one connector, and

remove the Scanner Assy Flat Cable.

4004D025AA

5. Unplug one connector and remove the harness

from one wiring saddle.

6. Remove two screws and the Original Glass Cool-

ing Fan Motor.

4004D018AB

Содержание CF1501















































































































































































































































































Результаты поиска

Содержание CF1501

Отзывы:

Бренды по названию

Популярные бренды

Minolta CF1501, Руководство по обслуживанию

Результаты поиска

Содержание CF1501

Отзывы:

Бренды по названию

Популярные бренды