manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, Руководство пользователя

Поделиться
Скачать
MINOLTA-QMS MAGICOLOR 6110 Скачать руководство пользователя страница 103

Status, Error, and Service Messages 

101

<x> DOOR OPEN

The specified cover is 
open and must be 
closed.

Close the cover.

FUSER JAM

Media has jammed leav-
ing the fuser area.

Locate and remove the 
jam.

FUSER MISINSTALLED

The fuser is not fully 
seated.

Make sure the fuser is 
fully seated.

FUSER OIL EMPTY

The fuser oil bottle for 
the fuser is empty. The 
printer will not print any 
more copies until a new 
fuser oil bottle is 
installed.

Install a new fuser oil 
bottle.

FUSER OIL LOW

The fuser oil bottle for 
the fuser unit is running 
low.

If you have a new fuser 
oil bottle on hand, you 
may want to install it 
now. If you don’t, order 
one now. A limited num-
ber of copies (about 
100) will still print. How-
ever, when the oil runs 
out, the printer stops and 
the 

FUSER OIL EMPTY

 

message appears.

IDLE

The printer is on line, but 
no jobs are in process.

No action needed.

INITIALIZING

The printer is warming 
up and getting ready to 
go on line.

Wait. No other action 
needed.

INNER JAM

Media has jammed leav-
ing the OPC belt car-
tridge area.

Locate and remove the 
jam.

INPUT BIN JAM

Media has jammed while 
being pulled from the 
specified tray.

This message...

means...

do this...

Содержание MAGICOLOR 6110

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды