manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 2210, Руководство пользователя

Поделиться
Скачать
MINOLTA-QMS MAGICOLOR 2210 Скачать руководство пользователя страница 106

Dual In-Line Memory Modules

104

Additional memory allows you to download more fonts and increase the 
printer's buffer (area where data sent from the computer is stored while 
waiting to be printed).

5

"

You will also need additional memory to duplex print at 1200 x 1200 
dpi on letter and legal media sizes.

How Much Memory Do You Need? 

The amount of RAM installed in your printer governs which resolutions can be 
used with each media size. 

If a certain resolution is chosen and the minimum amount of memory is not 
installed in the printer, the file is printed using the next lower resolution that 
can handle the job. For example, if you attempt to print a 4-color duplex 
image at 1200x1200 dpi resolution on legal media, but the printer has only 
128 MB of RAM instead of the required 256 MB minimum, the file prints at 
600x600 dpi.

The magicolor 2210 will print all print jobs at the highest resolution that the 
installed memory will support.

Minimum System Memory Requirements (in MB) 

You may also need additional memory (DIMMs) for the following:

Media 
Size

600x600 1200x1200

Mono Mono

Duplex

4-Color 4-Color

Duplex

Mono

Mono
Duplex

4-Color 4-Color

Duplex

Letter, A4

Basic*

* “Basic” memory requirement is the minimum memory required to print at the indicated 
resolution.
“Maximum Performance” memory requirement is the minimum memory required to 
achieve the maximum performance possible for any given job. The page rate, with maxi-
mum listed memory, will be determined solely by the complexity of the job.

128 

128 

128  

128  

128  

128  

128  

192 

Maximum 
Perform- 
ance

*

128  

128  

128  

128  

128  

128  

192 

256  

Legal

Basic

*

128  

128  

128  

128  

128  

128  

128  

256  

Maximum 
Perform- 
ance

*

128  

128  

128  

128  

128  

128  

256  

384  

Содержание MAGICOLOR 2210

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды