MINOLTA-QMS MAGICOLOR 2210 Скачать руководство пользователя страница 102

Страница: 102 / 176

Introduction

100

Introduction

This chapter provides information about the following accessories. Contact
your local vendor for purchase information.

5-bin Mailbox

Three models: For 100-, 120-, or 220-volt printers

Automatic Document
Feeder (ADF) for
SC-210/110

ADF for convenience copier

BuzzBox

Via parallel connection for 100, 120, and 220 volts

Dual In-Line Memory
Modules (DIMMs)

32, 64, or 128 MB, PC-100 Compliant SDRAM
DIMMs, up to a printer maximum of 384 MB

Duplex Unit

Automatic duplexing

Emulations,
Fonts, Utilities, and
Other Software

„

ImageServer

„

TIFF

„

CALS

„

LNO3

„

CGM

„

Kanji Font Internal IDE Hard Disk

„

QFORM

„

PlanetPress (forms-creation utility)

„

Fonts

Interfaces and
Daughterboards

„

Crown for DECnet-TCP/IP (equipped with
10BaseT)

„

CrownNet for Ethernet 10BaseT/100BaseTX
(equipped with RJ45 connector)

„

CrownNet for Token-Ring (equipped with STP
and UTP connectors)

„

SCSI Interface

Internal IDE Hard
Disk Drive

Used for storage of fonts, forms, and overlays; virtual
memory; and job spooling

Lower Feeder Unit
(LFU)

Media tray included

Media Tray, 500
Sheet

Purchasing extra trays may be convenient when
changing media formats and/or media qualities vary.

Printer Stand and/or
Cabinet

Various models available

Содержание MAGICOLOR 2210

















































































































































































Результаты поиска

Содержание MAGICOLOR 2210

Отзывы:

Бренды по названию

Популярные бренды

MINOLTA-QMS MAGICOLOR 2210, Руководство пользователя

Результаты поиска

Содержание MAGICOLOR 2210

Отзывы:

Бренды по названию

Популярные бренды