background image

serial

 

number

  

purchase

 

date

Master User Manual for

 RIPTIDE SF

BOW MOUNT 

HAND CONTROL 

SALTWATER 

MOTORS

Features

Assembly

Installation

Operation

Gas Assist

Cautions

Circuit Breaker

Battery Information

Battery Connection

Wiring Diagram

Propeller Replacement

Maximizer

Maintenance

Troubleshooting

Warranty

pg. 2

pg. 3

pg. 4-5

pg. 6-7

pg. 8

pg. 9

pg. 9

pg. 10

pg. 10

pg. 11

pg. 12

pg. 12

pg. 13

pg. 13

pg. 14

note

do

 

not

 

return

 

your

 

minn

 

kota

 

motor

 

to

 

your

 

retailer

. y

our

 

retailer

 

is

 

not

 

authorized

 

to

 

repair

 

or

 

replace

 

this

 

unit

. y

ou

 

may

 

obtain

 

service

 

by

• 

calling

 

minn

 

kota

 

at

: 1-800-227-6433 

or

   1-507-345-4623;

• 

returning

 

your

 

motor

 

to

 

the

 

minn

 

kota

 

factory

   

   

service

 

center

• 

sending

 

or

 

taking

 

your

 

motor

 

to

 

any

 

minn

 

kota

   

authorized

 

service

 

center

 

on

 

enclosed

 

list

.

please

 

include

 

proof

 

of

 

purchase

serial

 

number

 

and

 

purchase

 

date

 

for

 

warranty

 

service

 

with

 

any

 

of

 

the

 

above

 

options

.

PLEASE THOROUGHLY READ THIS USER MANU-
AL. FOLLOW ALL INSTRUCTIONS AND HEED ALL 
SAFETY & CAUTIONARY NOTICES BELOW. USE OF 
THIS MOTOR IS ONLY PERMITTED FOR PERSONS 
THAT HAVE READ AND UNDERSTOOD THESE USER 
INSTRUCTIONS. MINORS MAY USE THIS MOTOR ONLY 
UNDER ADULT SUPERVISION.

Содержание Riptide SF





















Отзывы: