Minimotors SpeedWay V, Руководство пользователя

Страница: 9 / 11

16
Speedway5 User Manual Speedway5 User Manual
17
(Unlocked status) (Locked status)
Fatigue failure parts and maintenance parts replacement cycle
SPEEDWAY Ⅴ
No Parts name Replacement cycle / km
1 HANDLE T BAR 2YEARS / 5,000
2
STEERING TUBE 2YEARS / 5,000
3 FOLDING FRAME 2YEARS / 10,000
4 FOLDING MOUNT 2YEARS / 5,000
5 FOLDING LOCKING SET 2YEARS / 3,000
6 FRONT SUSPENSION BOARD 2YEARS / 10,000
7 FRONT SUSPENSION 2YEARS / 7,000
8
REAR SUSPENSION ARM 2YEARS / 10,000
9 BATTERY 2YEARS / 20,000
10 Other chassis components If the exterior is damaged
or deformed
inside
Maintenance
④
⑦
③
②
⑤
⑥
①
③
* Completely separable hub motor design By designing the rim and hub
motor to be completely separable it is possible to replace only the rim
without replacing the entire motor when the rim breaks, thus improving the
maintenance and maintenance of the product. (Patent pending)
Easy-wheel system
3. How to check the folding lock device (S button lever)
Make sure that the folding lock (S button lever) is fully inserted with a clicking sound. Check the
fastening condition of the bolts and nuts of the near fixing parts.
* Caution: If folding lock device (S button lever) is not inserted correctly, it may cause damage due to
folding parts or collision.
1. Brake adjustment method
Hold the brake wire with the long nose and use the hexagon
wrench to unscrew the brake arm wire fixing bolt and lift the
brake arm upwards to narrow the braking distance and to better
catch the brake.
If you hear a sharp hissing sound when you hold the brake, dust
or sand particles on the ground will spill out on the surface of
the brake pad, the surface of the disc, or warping due to heat or
external impact. At this time, clean the inner surface of the disc
by turning the wheels with a clean, dry cloth, or straightening the bent discs.
2. How to adjust handle bar clearance
If there is a gap in the handle, turn the 1/4 turn counterclockwise
using a hexagon wrench to check the tucked bolt when the handle
is folded, then test it by unfolding the handle.
* Caution: If you turn too much, the handle will not fully extend. In
this case, tighten slightly clockwise again.
CHECK LIST
2) Maintenance and self-maintenance
Electric products can be damaged by various factors. The life span of each part
varies depending on driving habits and driving environment. Parts that exceed the
service life may cause accidents. Let's manage various parts and prevent safety
accidents in advance.
①
The components and suspension parts of the car swing arm, tires, tubes, wheels, bearings,
headset bearings, discs, brake pads, cables and folding parts, various brackets and other
consumable parts requiring periodic inspection and always check.
2. External damage inspection by driving environment
①
Replace parts that may be damaged by external driving environment, such as deformation of parts,
cracks due to compression, and signs of exceeding fine gold or life expectancy.
②
If the product is exposed to strong sunlight for a long time, discoloration may occur.
③
In case of heavy driving such as normal jumps, slight impacts such as turning, collision, etc., when
driving frequently or for a long time in a poor road condition or driving for thousands of kilometers
or more, fatigue breakdown phenomena Please check and replace the parts replacement schedule
for each product for safety.
④
Fatigue breakdown and maintenance parts may differ from the example conditions depending on
the driving environment and the operating conditions. Also check parts other than the replacement
cycle (maintenance parts) at all times to check for any signs of abnormality.
1. Check the replacement timing of consumable parts
inside
inside
⑧
⑨
inside
inside
Important checklist
*Metal vibration may occur due to motor vibration, vibration of the brake disc and pad during the load section that
accelerates during driving. (About 15 ~ 30Km, different for each product) This is a phenomenon in which all revolutions
(fans, automobiles, ships, etc.) are vibrating at a specific rotational frequency (rpm) rather than the product. However, if
the continuous noise or metal noise is large, there is a possibility that the disk is bent and deformed.
* Please note that after running, there is a risk of burns due to the heat on the motor and brake (especially disk rotor) side.
Important notice
3) Maintenance by self-maintenance
(Tool : 3mm, 5mm hexagon wrench)