Minebea CC-Link CSD-892-73 Скачать руководство пользователя страница 41

Страница: 41 / 159

tio

4-9. Calibration only of ZERO

This function is for calibrating again only of the ZERO when the amount of the tare other

than the maximum capacity of the measuring part are changed.

１

Change to calibration mode only for ZERO

Step

Measurement mode

Calibration mode only for ZERO

By pushing key from the normal measurement mode,

displays.

The display becomes . By pushing key,

displays.

Push key at three times. The display changes as follows:

→

▲

１

Calibration only for ZERO

Step

Measurement mode

Push key to finish this mode.

By pushing key , blinks and the calibration of

ZERO starts.

▲

By pushing key from the display of ,

* Please set the condition that nothing is put on the measuring part.

The calibration of ZERO is finished, and displays

By pushing key twice, you can return to the measuring mode.

Display becomes , the set data is memorized
to the internal memory.

After lights on, push key.

STABLE

→

By pressing key three times, display changes in order as

Display becomes , you can enter into the calibration
mode only for ZERO.

displays.

ENTER

FUNC.

CAL-Z

ENTER

CAL-Z

ENTER

FUNC.

Error display of ZERO calibration

blinks for about 2 seconds when the load cell output value exceeds over ZERO adjustment

range at minus side (at -2.5 mV/V or more)

blinks for about 2 seconds when the load cell output exceeds over zero adjustment

range at plus side (at 2.5 mV/V or more), or the value of [Registered SPAN + ZERO

registering again] exceeds over 3.1 mV/V.

* Please con

ﬁ

rm the rated capacity and the tare amount, etc., so that the ZERO should not exceed the adjustable

range.

Содержание CC-Link CSD-892-73
































































































































































Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Minebea CC-Link CSD-892-73, Инструкция по эксплуатации, Страница: 41 / 159

Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы: