Minebea CC-Link CSD-892-73 Скачать руководство пользователя страница 23

Страница: 23 / 159

tio

n &

irin

2-6. Connection of CC-Link interface

The cable only for CC-Link is wired to the attached connector for CC-Link, and connected

as shown in the

ﬁ

gure below.

●

For connection of CC-Link cable, use a twisted pair cable line with shield (Cable only for

CC-Link) and connect a shield with SLD terminal.

●

Stripped length of electrical cable tip is 6 mm.

●

The tightening torque of terminal screws on the terminal block is 0.6 N

･

●

When you connect with this instrument, please check the direction of upper/lower sides

of the connector, and insert until it bumps.

CC-Link interface connector

Attached CC-Link interface

connector

Cable only for CC-Link

interface.

Signal line DA side
Signal line DB side
Signal ground
Shield
Frame ground

•

Attached connector for CC-Link : MSTB 2,5-ST-5,08 AU(by PHOENIX CONTACT)

•

As to the termination, connect the terminating resistance of 110

with the CC-Link

connector which is the furthest from PLC as possible.

•

The connecting cable must use the cable only for CC-Link.

•

Refer to the [Construction and speci

ﬁ

cation of network system] from the latest

version of CC-Link Cable Wiring Manual published by CC-Link Partner Association

about communication speed and cable length.

•

[SLD] and [FG] are connected internally.

•

Please refer to [5. Applied standard] in [Safety Precaution] about the grounding to

comply with CE Standard.

Содержание CC-Link CSD-892-73
































































































































































Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Minebea CC-Link CSD-892-73, Инструкция по эксплуатации, Страница: 23 / 159

Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы: