Minebea CC-Link CSD-892-73 Скачать руководство пользователя страница 12

Страница: 12 / 159

1. Each Name and Function

①

Unit display section

Display the setting unit of weighing.

②

Load display section

Display the Gross/Net, Overload or Error.
In the various setting mode, display the condition and the setting value.

③

Condition display section

Display the condition of CSD-892-73.
ZERO

Light on when the zero calibration is processed.

SPAN

Light on when the span calibration is processed.

mV/V

Light on when mV/V value is displayed, like in the calibration by the

numeric input, or in monitoring the output value from load cell.

STABLE

Light on when the weighing data is in stable condition.

TARE

Light on when the tare weight cancellation is processed.

GROSS

Light on when the display of weighing is set to the gross value.

NET

Light on when the display of weighing is set to the net value.

Light on when the displayed load value is zero, and within 1/4 of the

scale intervals.

LOCK

Light on when the key lock is effective.

HOLD

Light on when the holding is effective.

ERROR

Light on when the error signal is output.

OUT1 ~ 5 The number lights on when the corresponding external output is turning on.

1-1. Front panel

①

Unit display

③

Condition display

⑨

USB interface

connector

⑧

F/ENTER key

⑤

FUNC. key

⑦

CAL-S/

▲

key

⑥

CAL-Z/ key

②

Load display

④

Status LED

Содержание CC-Link CSD-892-73
































































































































































Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Minebea CC-Link CSD-892-73, Инструкция по эксплуатации, Страница: 12 / 159

Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы: