manualshive.com logo in svg

Minebea Intec Puro LargeCount EF-LT P1, Руководство по эксплуатации

Поделиться
Скачать
Minebea Intec Puro LargeCount EF-LT P1 Скачать руководство пользователя страница 11

3.1.5

Leveling the weighing platform

To achieve reproducible weighing results at all times, the weighing platform must be set
up to be precisely horizontal.

Therefore the weighing platform must be re-leveled every time it is moved to a different
location.

Leveling the weighing platform

3.1.6

Acclimatizing the device

If a cold device is brought into a warm environment, condensation may form.

3.2

Connection

3.2.1

Electrical supply

The scale is supplied using a power supply unit, unless a battery supply is required.

Connect the USB-C male plug connector with the USB-C female plug connector on the
underside of the device, then connect the power supply unit to the wall socket.

Note:

Do not use the USB-C connector cable for the PC communication. Instead, use a
standard USB-C cable.

3.2.1.1

Battery power

The scale can be operated immediately with the power supply. In order to operate the
scale with the battery, the battery should first be charged for 12 hours. If there is a power
outage or if the power cord is disconnected, the scale switches into battery operation
automatically. In the event of supply via a power supply, the battery is constantly charged
meaning that the battery charging display (see Chapter

4.1.2

) is continuously illuminated.

The scale can be used during the charging process; the battery is protected against
excess charging.

When the device is switched on, the battery status LED illuminates in red while the battery
is charging, and it goes green when the battery is fully charged.

.

Use the adjustable feet to align the weighing platform so that the air bubble of the
level indicator is in the center of the circle.

.

Check that all four of the adjustable feet are touching the surface.

The weight of the platform must be spread equally across the adjustable feet.

.

Adjust the adjustable feet: Retract the adjustable feet (clockwise) in order to lift the
scale. Extend the adjustable feet (counter-clockwise) in order to lower the scale.

.

Keep the device disconnected from the mains and allow it to acclimatize at room
temperature for approx. two hours.

3 Device installation

Compact scale Puro® LargeCount

Minebea Intec

EN-9

Содержание Puro LargeCount EF-LT P1

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды