Minebea Intec CAS1 Скачать руководство пользователя страница 118

Страница: 118 / 160

11 Error messages

A diferentiation is made between the following errors:

Dynamic errors are displayed with an error code (e.g. INF 01) for the duration of the

error.

Temporary errors are displayed for 2 seconds (e.g. INF 07)

Fatal errors are displayed permanently (e.g. ERR 101, can only be rectiied via reset)

Display

Cause

Remedy

No display seg-

ments

There is no operating voltage

Check electrical supply

-------

Key has no function in this state

Flashing

Battery defective or time adjusted

Set time

Weighing range has been exceeded

Unload the scale

L or ERR 54

Load plate is not positioned on the weighing

platform

Place the load plate onto the weighing

platform

ERR 101–104

Key stuck

Key pressed when switching on

Release key or

consult Minebea Intec customer service

ERR 320

Operating program memory defective

consult Minebea Intec customer service

ERR 335

Veriiable weighing platform does not match the

connected terminal

Connecting a suitable weighing platform

ERR 340

New EEPROM loaded (service)

Switch the scale of and on again; if

ERR 340 is permanently displayed, cont-

act Minebea Intec Customer Service

ERR 341

RAM lost data; battery empty

Leave device switched on for at least

10 hours

ERR 343

Data loss in the memory for transaction number

external Alibi memory

consult Minebea Intec customer service

INF 01

Data output does not it in the output format

Make correct setting in the setup menu

INF 02

Calibration condition was not complied with, e.g.

not tared or load plate loaded

Only adjust after zero display, unload sca-
le, tare with key

INF 03

The calibration process could not be completed

within a certain time.

Allow the device to warm up and then re-

calibrate the device

INF 06

Integrated calibration weight defective

consult Minebea Intec customer service

INF 07

The last used function is not allowed for veriied

scales

consult Minebea Intec customer service

INF 08

The load on the scale is too heavy to carry out ze-

roing

Please check whether the "power-on zero

range" (menu item [INIT.NUL] 1.12) was

complied with during the coniguration.

INF 09

No tare possible at gross zero

Zero the scales

INF 10

Tare not possible with assigned tare memory

Combics 1 Series Complete Scales Models CAW1P, CAW1S, CAS1

11 Error messages

EN-116

Minebea Intec

Содержание CAS1

































































































































































Результаты поиска

Содержание CAS1

Отзывы:

Minebea Intec CAS1, Руководство по эксплуатации, Страница: 118 / 160

Результаты поиска

Содержание CAS1

Отзывы: