Mindray Passport V Скачать руководство пользователя страница 69

Страница: 69 / 288

Menus: ECG Main and Submenus

ECG Monitoring

4 - 8

0070- 0-0704-02

Passport V Operating Instructions

4.4.2

Arrhythmia Menu (optional)

FIGURE 4-7

Arrhythmia Menu

NOTE:

The Arrhythmia Menu is disabled if Patient Size = Neonate.

ECG Sizes Menu

0.125 cm/mV
0.25 cm/mV
0.5 cm/mV

1 cm/mV

(default)

2 cm/mV
4 cm/mV

Select to open the ECG Sizes Menu.

Sets the ECG size (waveform gain) for:
• ECG1 only if using 3-lead
• ECG1 to ECG6 if using 5-lead

All ECG waveforms are displayed with 1cm/mV gain
in the

All ECG View

(via

View

key).

All ECG waveforms are displayed with the
user-selected gain after exiting the

All ECG View

All ECG waveform gains remain unchanged after
switchover between 3-lead and 5-lead modes.

NOTE:

The SIZE key on the front panel is used to

change ECG1 waveform size. The “ECG1 Size”
menu option in the

ECG Sizes Menu

has the same

function. (In

All ECG View

, this key is disabled.)

ECG Setup

Select to open the ECG Setup Menu.
See section 4.4.4 (pg. 4-12) "ECG Sizes Menu".

Resp Menu

Select to open the Respiration Menu.
See section 4.4.5 (pg. 4-12) "ECG Setup Menu".

ECG Menu

MENU ITEM

SELECTIONS

COMMENTS

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды