Mindray Passport V Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 288

background image

Passport V Operating Instructions

0070- 0-0704-02

3 - 11

Patient Management

Monitor/Display Troubleshooting

3.6

Monitor/Display Troubleshooting

MESSAGE/PROBLEM

REASON

SOLUTION

No trace for a desired
parameter

Improper attachment of
transducer or cable to monitor.

Check transducer / cable
connection.

Faulty transducer or cable.

Try a new transducer or cable.

Display Appears to be Off

Mains power switch may not be
on.

Press mains power switch on
side panel.

Unit may not be plugged into an
AC outlet.

Check power cord (Is it plugged
in

?

)

If used as a portable, battery
pack may be drained.

If battery pack is drained, plug
into an AC outlet to recharge the
battery. A period of 5.5 hours
(monitor OFF) or 8.5 hours
(monitor ON) is required for a
full charge of lithium-ion
batteries.

Monitor or display is damaged.

Contact Customer Support.

Disabled Alarm Tone

Silence

key pressed.

Check for alarm silence symbol
and message.

Beep volume low.

Increase beep volume.

Cooling Fan Failure

The unit running on AC power
and the cooling fan is not
operational.

Contact Customer Support.

Patient Information did not
appear on display

No data entered.

Enter proper patient data.

Done

was not selected from

keypad after entering data.

Go to the proper keypad enter
data, select

Done

when

finished.

Incorrect Date or Time

Data not entered or entered
incorrectly.

Follow instructions from

to Set the Clock / Date and
Time”

.

«
...
58
59
60
61
62
...
»

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Stubborn Dog In-Ground Radio Fence

Бренд: Petsafe Страницы: 22

Бренд: Geberit Страницы: 64

Mobile PowerWrap HBP4000

Бренд: Soft Heat Страницы: 24

UltraSculpt Mini

Бренд: La parfait Страницы: 8

Бренд: GUARDIAN GEAR Страницы: 2

EYENIMAL AUTOMATIC LASER

Бренд: Num'axes Страницы: 9

SOFY-PLANT gel GL-205

Бренд: Orliman Страницы: 11

Бренд: BaByliss PRO Страницы: 16

Бренд: Bumper Boy Страницы: 22

Passport PPA19-20559

Бренд: Petsafe Страницы: 17

UltiMate 3000 LCi

Бренд: Dionex Страницы: 42

KittySalon Groomer

Бренд: Watchorn Products Страницы: 4

Бренд: Frisco Страницы: 2

Бренд: DogWatch Страницы: 4

Бренд: DogWatch Страницы: 4

Бренд: Dogtra Страницы: 29

Бренд: Dogtra Страницы: 31

Бренд: ichigo ichie Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды