Mindray BeneFusion SP3 Скачать руководство пользователя

Страница: 33 / 80

3-9

alarm normally.

4. Install the syringe, set the infusion parameters correctly, and press the Start key

to enter the running screen.

5. The running icon, speed, accumulated volume, and pressure value during the

infusion process are normal.

Battery Powered Test:

1. After the AC power is disconnected for a short time, the battery should be able to

supply power independently.

2. The LED can generate a normal prompt when the battery is not installed or when

the battery is charged or discharged.

WARNING



The battery in this equipment is not removable. Battery replacement

must be performed by a service technician authorized by Shenzhen

Mindray Scientific Co., Ltd.. Installing a fuel cell or replacing the battery

with a person who is not fully trained by Shenzhen Mindray Scientific

Co., Ltd. can result in hazards (Such as overheating, fire, or explosion).

3.6 Electrical Safety Tests

WARNING



The electrical safety test is to verify the electrical safety of the syringe

pump. It is used to detect abnormal electrical hazards. If these hazards

are not detected in time, it may cause harm to the patient or the operator.



All tests can be performed using commercially available safety analyzer

test equipment. Maintenance personnel shall ensure the adaptability,

functional completeness and safety of the test equipment, and be

familiar with their usage.



Electrical safety tests shall comply with the following standards: EN

60601-1 and GB9706.1.



In case of other stipulations in local laws and regulations, implement

electrical safety tests by following relevant stipulations.



All devices driven by AC power and connected to medical instruments in

patient zones must comply with the IEC/EN 60601-1 and GB9706.1

standards. And electrical safety tests on these devices must be

implemented in accordance with the test interval of the monitor.

Содержание BeneFusion SP3

















































































Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды

Mindray BeneFusion SP3, Руководство по обслуживанию

Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды