Mindray BeneFusion SP3 Скачать руководство пользователя

Страница: 18 / 80

2-6

2.3.1 Control board

The SP3 control board consists of three parts, the power supply part, the main

control part and the monitoring part.

The power supply part includes an ACDC conversion module, an on/off control

circuit, a DC power conversion circuit, a standby sound and light alarm circuit, and a

battery charge and discharge management circuit.

The ACDC conversion module converts the input AC power supply of 100-240VAC

and 50/60Hz to an output of DC 15V.

The on/off control circuit can combine three power inputs of ACDC input, external

DC input, and internal battery into VBUS, and the priorities of ACDC input and

external DC input are higher than that of internal battery; the on/off signal can

convert VBUS into VPP output.

VBUS is not controlled by the on/off signal, but VPP is controlled by the on/off signal.

VBUS is stepped down to VCCB (5V) through the LDO circuit (U9 TLV70450).

VCCB is stepped down to VBB (3.3V) through the LDO circuit (U13 SPX5205). VPP

is stepped down to VCC (5V) through the Buck circuit (U11 TPS5420D). VCC is

stepped down to VDD (3.3V) through the LDO circuit (U12 SPX1117M3). VPP is

boosted to VMM (+18.9V) through the Boost circuit (U6 TPS61175PWP).

The main control CPU controls on/off and provides motor power failure protection

under single fault condition. The monitoring CPU monitors the battery charging

status, detects the power status of each module, controls the battery LED, and

communicates with the CPU of the main control module through the serial port. After

being triggered by the on/off key from the keypad, the main control CPU and the

monitoring CPU simultaneously output the power-on lock signal and the module

power enable signal, so that VCC, VDD, and VMM are sequentially output, and the

entire system is powered on. When the normal shutdown is required, after the main

control CPU detects the shutdown signal, it notifies the monitoring CPU to cancel

the power-on lock signal through the serial port, and finally the main control CPU

completes the shutdown.

Battery charging and discharging management circuit adopts BQ24103RHLR. The

on/off charging current is designed to both 650±50mA (The charging time of the

single battery does not exceed 6 h. The charging time of the dual battery does not

exceed 12 h). The battery is at a voltage of 8.1±0.2V when fully charged.

When the battery voltage is too low and the AC power and external DC power are off,

the backup sound and light alarm circuit triggers the buzzer to sound at a frequency

of 2.73Hz±0.5V, and drives the red alarm lamp to be continuously illuminated.

When the monitoring CPU detects that the VDD power supply is abnormal or the

communication with the CPU of the main control module is abnormal, the buzzer

sounds and the power of the stepper motor is turned off.

Содержание BeneFusion SP3

















































































Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды

Mindray BeneFusion SP3, Руководство по обслуживанию

Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды