Mindray Accutorr V Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 130

background image

Accutorr V Operating Instructions

0070-10-0699-02

3 - 29

Operation

SpO

2

Measurements

CAUTION:

Inaccurate readings may be caused by incorrect sensor
application or use; significant levels of dysfunctional
hemoglobins (i.e. carbohemoglobins or methemoglobin); or
intra-vascular dyes such as indocyanine green or methylene
blue; exposure to excessive illumination, such as surgical
lamps (especially ones with a Xenon light source), bilirubin
lamps, fluorescent lights, infrared heating lamps, or direct
sunlight; excessive patient movement; venous pulsations;
electro-surgical interference; and placement of a sensor on
an extremity that has a blood pressure cuff, arterial
catheter, or intra-vascular line.

CAUTION:

Route cables neatly. Ensure cables, hoses, and wires are
kept away from patient’s neck to avoid strangulation. Keep
floors and walkways free of cables to reduce risk to
hospital personnel, patients, and visitors. If the sensor or
patient cable is damaged in any way, discontinue use
immediately.

NOTE:

Do not place the sensor on an extremity with an invasive
catheter or blood pressure cuff in place.

NOTE:

In certain situations in which perfusion and signal strength
are low, such as in patients with thick or pigmented skin,
inaccurately low SpO2 readings will result. Verification of
oxygenation should be made, especially in preterm infants
and patients with chronic lung disease, before instituting
any therapy or intervention.

The digital SpO

2

value displays on the SpO

2

LED (7), and the SpO

2

Pulse Rate displays on

the Pulse Rate LED (6).

3.

If desired, adjust the beep volume. See section 3.10.1, “Setting the Alarm Volume, Key
Volume, and Pulse Volume, and NIBP End Tone Volume”, for details on adjusting the
beep volume.

3.11.2.1

NELLCOR

®

Sensors

NELLCOR

®

provides a family of sensors suitable for a wide variety of clinical settings and

patients. See package insert(s) for use and care instructions. Additional information is
available from Nellcor Puritan Bennett Inc. at www.nellcor.com.

3.11.3

Sequence for Establishing SpO

2

with Masimo

®

Pulse Oximetry

This is an optional feature.

1.

Select the appropriate sensor for the patient from the list of accessories in Chapter 5.0 .

2.

Attach the appropriate corresponding Patient Cable (P/N 0012-00-1099-02, 0012-00-
1652, 0012-00-1599, or 0012-00-1653) to the sensor and plug the other end of the
patient cable into the SpO

2

connector (20).

CAUTION:

When equipped with MASIMO® SpO2, use only MASIMO®
oxygen transducers including MASIMO LNOP®, MASIMO
LNCS® patient dedicated adhesive sensors and MASIMO PC
Series Patient Cable. Use of other oxygen transducers may
cause improper oximetry performance.

CAUTION:

Excessive ambient light may cause inaccurate SpO2
measurements. Cover the sensor with opaque materials.

«
...
56
57
58
59
60
...
»

Содержание Accutorr V



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Accutorr V

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: Farmet Страницы: 102

Бренд: Jackco Страницы: 6

Бренд: Velp Scientifica Страницы: 12

Бренд: Yamaha Страницы: 24

Бренд: J&M Страницы: 33

Бренд: Lalizas Страницы: 12

BOBCAT 130 Series

Бренд: Balcrank Страницы: 12

Бренд: Ublox Страницы: 22

Бренд: v.link Страницы: 20

Бренд: BCP Страницы: 8

Бренд: Meyer Страницы: 100

Rovelight RT-400

Бренд: Orlit Страницы: 16

Бренд: Turner Designs Страницы: 55

Бренд: Almat Страницы: 4

Бренд: ITEM Страницы: 12

Бренд: Shel lab Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды