MIMAKI Textile Jet Tx3-1600 Скачать руководство пользователя страница 111

Страница: 111 / 218

- 3.3 -

Cleaning inside of the cleaning water tank

Clean inside of the cleaning water tank regularly.

After a certain period of time using the cleaning water , it may fine away by natural evaporation,

etc. The cleaning water volume may become less, the warning message shows on the LCD as below.

Replacing the water of the tank

It is necessary to change water every day when belt cleaning is being performed with water circula-

tion. The dirty water is pumped up with attached hand pump and then pour clean water into the tank.

• When belt cleaning is being performed with water circulation, change

cleaning water every day.

• Dispose of waste cleaning water according to the local regulations.

Pump up the dirty water from the tank to an-

other polyethylene tank by hand pump.

Make sure to close the sewer valve.

Fill the tank with about 20 liters of water.

Sewer valve

Wash Tank

Check The Water

Содержание Textile Jet Tx3-1600



























































































































































































































Результаты поиска

Содержание Textile Jet Tx3-1600

Отзывы:

Похожие инструкции для Textile Jet Tx3-1600

Бренды по названию

Популярные бренды

MIMAKI Textile Jet Tx3-1600, Руководство по эксплуатации

Результаты поиска

Содержание Textile Jet Tx3-1600

Отзывы:

Похожие инструкции для Textile Jet Tx3-1600

Бренды по названию

Популярные бренды